Kanalgeräte Fdum Installieren - S-Klima S-Serie Technisches Handbuch

8 1 1 4
For heat insulation For pipe
For unit For heat insulation
hanging of gas pipe of liquid tube cover fixing
· Places where cosmetics or special sprays are
Innengeräte installieren
frequently used.
· Highly salted area such as beach.
②Selection of installation location for the indoor unit
· Heavy snow area
· Places where the system is affected by
smoke from a chimney.
① Select the suitable areas to install the unit under approval of the user.
· Altitude over 1000m
10.4 Kanalgeräte FDUM installieren
・Areas where the indoor unit can deliver hot and cold wind sufficiently. Suggest to the user to use
a circulator if the ceiling height is over 3m to avoid warm air being accumulated on the ceiling.
・Areas where there is enough space to install and service.
Do not install the motion sensor at following
Dieses Gerät ist für mittleren statischen Druck ausgelegt. Deshalb sollte das Gerät nicht als Kli-
・Areas where it can be drained properly. Areas where drain pipe descending slope can be
places. It could cause detection error, incapacity
of detection, or characteristic degradation.
taken.
magerät für direkte Ausblasung verwendet werden.
· Place where vibration is applied to it for a long
・Areas where there is no obstruction of air flow on both air return grille and air supply port.
period of time.
Befolgen Sie die Anweisungen des Handbuchs.
・Areas where fire alarm will not be accidentally activated by the air-conditioner.
· Place where static electricity or electromag-
Überprüfen Sie die Vollständigkeit folgender Punkte:
netic wave generates.
・Areas where the supply air does not short-circuit.
· Place where it is exposed to high temperature
・Areas where it is not influenced by draft air.
or humidity for a long period of time.
● Gerätetyp
・Areas not exposed to direct sunlight.
· Dusty place or where the lens face could be
・Areas where dew point is lower than around 28°C and relative humidity is lower than 80%.
Spezifikation der Stromversorgung fouled or damaged.
●
This indoor unit is tested under the condition of JIS (Japan Industrial Standard) high humidity
●
condition and confirmed there is no problem. However, there is some risk of condensation Leitungen, Kabel, Kleinteile
drop if the air-conditioner is operated under the severer condition than mentioned above.
● Zubehörteile
If there is a possibility to use it under such a condition, attach additional insulation of 10 to
20mm thick for entire surface of indoor unit, refrigeration pipe and drain pipe.
Zubehörteile:
・Areas where TV and radio stays away more than 1m. (It could cause jamming and noise.)
・Areas where any items which will be damaged by getting wet are not placed such as food,
Aufhängung
table wares, server, or medical equipment under the unit.
Unterlegscheibe Rohrverkleidung
・Areas where there is no influence by the heat which cookware generates.
(M10)
・Areas where not exposed to oil mist, powder and/or steam directly such as above fryer.
・Areas where lighting device such as fluorescent light or incandescent light doesn't affect
the operation.
Betondecke
(A beam from lighting device sometimes affects the infrared receiver for the wireless remote
control and the air conditioner might not work properly.)
8
② Check if the place where the air-conditioner is installed can hold the weight of the unit. If it is
Zur Wärmeisolierung
Zur Aufhängung
Raumdecke
not able to hold, reinforce the structure with boards and beams strong enough to hold it. If the
der Saugleitung
des Geräts
strength is not enough, it could cause injury due to unit falling.
100-200
Abstände für Installation und Service
Space for installation and service
●
Das Innengerät muss in einer Höhe von mindestens 2,5 m angebracht werden.
●Make installation altitude over 2.5m.
(Indoor Unit) Wählen Sie eines der beiden Installationsbeispiele zum Einhalten der Mindestabstände:
●
Select either of two cases to keep space for installation and services.
Installationsbeispiel 1 - Seitenansicht des Geräts
Wartungs-
öffnung
(450x450)
Wartungs-
öffnung
Anm. (a)
B
Notes (a) There must not be obstacle to draw out fan motor. (
Größe der Wartungsöffnung
(b) Install refrigerant pipe, drain pipe, and wiring so as not to cross
FDUM
40-50
Installationsbeispiel 2 - Ansicht des Geräts von unten A 1100
B
Anmerkungen: (a)
Wartungs-
öffnung
168
1 1 1
For heat insulation For heat insulation For drain pipe
For drain hose
of drain socket of drain socket connecting mounting
Einheit: mm
Für Kältemittelleitung
Rohrverkleidung
Band
(groß) (klein)
Anm. (b)
1 1 4
Zur Wärmeisolierung
Zur Befestigung
der Flüssigkeitsleitung
der Rohrverkleidung
370
marked area)
marked area.
Einheit: mm
Anm. (b)
Betondecke
Raumdecke
370
100-200
marked area)
Einheit: mm
60
1300
620
Es dürfen sich keine Hindernisse im Ausblasbereich des Ventilators
befinden.
(b) Kältemittelleitungen, Kondensatleitungen und Verkabelung müssen so
installiert werden, dass sie nicht in den markierten Bereich ragen.
B
Größe der Wartungsöffnung
Einheit: mm
FDUM
40-50 60
A 1100 1300
B 620
1
・Areas where the supply air does not short-circuit.
Accessory parts are stored
・Areas where it is not influenced by draft air.
inside this suction side.
・Areas not exposed to direct sunlight.
・Areas where dew point is lower than around 28°C and relative humidity is lower than 80%.
This indoor unit is tested under the condition of JIS (Japan Industrial Standard) high humidity
condition and confirmed there is no problem. However, there is some risk of condensation
drop if the air-conditioner is operated under the severer condition than mentioned above.
Multi type
If there is a possibility to use it under such a condition, attach additional insulation of 10 to
Single type
20mm thick for entire surface of indoor unit, refrigeration pipe and drain pipe.
・Areas where TV and radio stays away more than 1m. (It could cause jamming and noise.)
・Areas where any items which will be damaged by getting wet are not placed such as food,
table wares, server, or medical equipment under the unit.
・Areas where there is no influence by the heat which cookware generates.
Pipe locations UNIT: mm
・Areas where not exposed to oil mist, powder and/or steam directly such as above fryer.
・Areas where lighting device such as fluorescent light or incandescent light doesn't affect
Multi type
the operation.
Single type
(A beam from lighting device sometimes affects the infrared receiver for the wireless remote
control and the air conditioner might not work properly.)
② Check if the place where the air-conditioner is installed can hold the weight of the unit. If it is
not able to hold, reinforce the structure with boards and beams strong enough to hold it. If the
strength is not enough, it could cause injury due to unit falling.
Space for installation and service
●Make installation altitude over 2.5m.
④Installation of indoor unit
(Indoor Unit)
Für Kondensatleitung
Select either of two cases to keep space for installation and services.
Rohrverkleidung Rohrverkleidung
Multi type
(groß) (klein)
Installationsbeispiel 1 - Seitenansicht des Geräts
Installation
Single type
[Hanging]
Hang the unit up.
Wartungs-
1 1
öffnung
(450x450)
Zur Wärmeisolierung des
Kondensatanschlusses
Anm. (a)
Notes (a) There must not be obstacle to draw out fan motor. (
(b) Install refrigerant pipe, drain pipe, and wiring so as not to cross
Adjustment for horizontality
Installationsbeispiel 2 - Ansicht des Geräts von unten
Einheit: mm
④Installation of indoor unit
○Either use a level vial, or adjust the level according to the method below.
Installation
●Adjust so the bottom side of the unit will be leveled with the water surface a
illustrated below.
[Hanging]
Wartungs-
Hang the unit up.
öffnung
marked area.
Adjustment for horizontality
Einheit: mm
○If the unit is not leveled, it may cause malfunctions or inoperation of the float s
○Either use a level vial, or adjust the level according to the method below.
- -
156
○If the unit is not leveled, it may cause malfunctions or inoperation of the float switch.
Technisches Handbuch S-Serie R32 | Ausgabe 11-01-2023 | 20007503
Refrigerant gas pipe
Refrigerant liquid pipe
Einlasskanal
Multi 22-56 71, 90
112-160
Single 40-50 60, 71
100-140
A 786 986
B 472 472
C 135 135
22-90
40-71
Refrigerant gas pipe
Refrigerant liquid pipe
Refrigerant gas pipe
Refrigerant liquid pipe
Kondensatschlauch Schlauchschelle
112-160
100-140
Suspension bolt
1 1
Betondecke
M10 nut
Washer for M10
Zum Verbinden mit Zur Montage des
Die Zubehörteile befinden
der Kondensatleitung Kondensatschlauchs
sich im Gerät auf der Saugseite
Raumdecke
Unit
Spring washer for M10
Refrigerant gas pipe
100-200
Refrigerant liquid pipe
Pipe side
Suspension bolt
Pour water
M10 nut
B
Washer for M10
Water
surface
Unit
Spring washer for M10
0~5mm
Größe der Wartungsöffnung
Einheit: mm
FDUM
40-50 60
A 1100 1300
Let the pipe side be slightly sloped.
B 620
●Adjust so the bottom side of the unit will be leveled with the water surface as
illustrated below.
Pipe side
Pour water
Water
surface
0~5mm
Let the pipe side be slightly sloped.
○ Halten Sie die
Maße für die
Gerät
467
Aufhängungsbolzen
aus der
untenstehenden
(For natural drainage)
Tabelle ein.
drain pipe connection VP20 (PVC pipe
Einheit: mm
112-160
100-140
1404
530
635
180
468
405
467
510
471
(For natural drainage)
413
drain pipe connection VP20 (PVC pipe
drain pipe connection
(PVC pipe) (Drain hose V
467
(For natural drainage)
drain pipe connection VP20 (PVC pipe)
Einheit: mm
635
468
405
Anm. (b)
If the measureme
the unit and the c
drain pipe connection
(PVC pipe) (Drain hose V
not match upon in
467 may be adjusted w
370
holed installation
(For natural drainage)
drain pipe connection VP20 (PVC pipe)
marked area)
marked area.
Einheit: mm
If the measurements betw
the unit and the ceiling ho
not match upon installatio
may be adjusted with the
holed installation tool.
Vinyl hose
-
156
Vinyl hose
(PVC pipe) (Dr
Multi
Singl
Multi
Singl
drain pipe con
(PVC pipe) (Dr
④I
Inst
[Ha
Han
Adju
○E
●
○If
-