Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
indicator (3) in the right cooking zone
and the led (25) above the sensor
(23) illuminates, indicating that
the function has been activated. The
phase of PREHEATING of the paella
pan with the oil begins. The CALENTAR
the phase. Once the preheating
is complete, an acoustic signal is
of the symbol
and the led (26)
the oil is hot and, therefore, this phase
has been completed.
It is time to add the meat and move
on to the next phase, if you consider
it appropriate. Pressing the sensor
(24) starts the stir-frying phase of
the meat. The CARNE led (27) starts
flashing, and the power is adjusted
automatically to sauté the meat during
this period. At the end of the suggested
time to fry the meat there will be an
acoustic signal accompanied by the
that you can move on to the next
phase if you consider it appropriate.
The elapsed time for each cooking
phase is displayed on the timer clock
indicator (12) in the central area (in
then in minutes).
Press the sensor
(24) and then add
the vegetable, to start your stir-frying
phase. The VERDURA led (28), will
phase. After three minutes of this, add
a little oil, garlic and peppers, stirring
and immediately adding the crushed
tomato. At the end of the suggested
time to fry the vegetable there will be
an acoustic signal accompanied by the
that you can move on to the next phase
if you wish.
Add the water and press the sensor
(24) to continue preparing the
broth. The CALDO led (29), will begin
to flash, indicating the start of the
phase. After three or four minutes it is
time to season it with salt. At the end
of the suggested time for cooking the
broth there will be an acoustic signal
symbol
move on to the next phase if you
consider it appropriate.
spread it well throughout the paella
pan. Then press the sensor
indicating that the rice cooking phase
has begun. At the end of the suggested
time for cooking the rice there will be
an acoustic signal accompanied by
the flashing of the symbol
if you wish, or proceed to the creation
of the socarrat.
sensor
stop. Then let the rice stand for at least
If, on the other hand, you want to
and the led
achieve a final finish with socarrat:
add a thread of olive oil on the surface
of the rice and then press the sensor
(24). The SOCARRAT led (31) will
has started. Be attentive because, at
the end of the suggested time for the
elaboration of the socarrat, an acoustic
signal is produced, accompanied by the
remove the paella pan from the heat
and let it sit for at least 2 minutes.
Observations:
• The acoustic signal at the end of
each phase indicates the end of the
suggested time, although the actual
phase continues to work until the user
and the led
decides to move on to the next, touching
the sensor
• If you do not change the phase,
the cooker will emit a new acoustic
signal every minute that elapses,
leds that are already on (27, 28, 29, 30
or 31), reminding that the suggested
time for that phase has already been
surpassed.
and the led (29) will begin
(24).
and
(23) and the function will
and the led
(24).
• At the beginning of each cooking
phase, the timer clock indicator (12) is
activated indicating the time elapsed in
each stage. When changing phases the
time restarts.
• If you mistakenly change phases
without wishing to, you can return to the
previous phase by pressing the sensor
several times (24) until you select
the desired phase again. Note that the
time of the selected phase will be
counted again from the start.
Special functions: CHEF
(depending on the model)
These functions have pre-allocated
power levels to make cooking easier,
obtaining excellent results as the
temperature of the pan is controlled
continuously by sensors. When the
target temperature for the function
has been reached, it is automatically
maintained without needing to change
the power level.
The CHEF functions operate correctly
with pans with the same ferromagnetic
area on the base of the pan as the
area of the cooking zone. In addition,
for high temperature functions (above
base (preferably "sandwich" type) as
Fig. 9
To ensure the correct operation of these
functions, it is important that the pan and
the cooking zone are not hot at the start
of the process.
Further information about suitable pans
(saucepans, frying pans, grills, etc.) is
given on the Teka web page.
The Touch Control has special features
that help the user to cook through the
CHEF sensor
(14). These functions
are available depending on the model.
To activate a special feature on a zone:
1 First it should be selected; and then,
the decimal point (4) will be active on
EN
35
Werbung
Inhaltsverzeichnis
