Teka IZC 63632 MST Montageanleitung Und Empfehlungen Zur Verendung Und Wartung Seite 36

EN
the power indicator (3).
2 Now click on the CHEF sensor
(14). The sequentially successive
presses will go over all the CHEF
functions available in each zone one
by one. These functions will show
the activation with the corresponding
leds (15), (16), (17), (18), (19) ,(20),
(21) and (22).
If you want to cancel a special active
function at any time, you should touch
the "slider" cursor sensor (2) of the
related zone to select it. The decimal
point (4) of the power indicator (3) will
light up. Then, touch again the "slider"
(2) cursor to set a new power level or to
on the CHEF sensor (14).
MANTENER CALIENTE FUNCTION
(depending on the model)
This function automatically sets an
appropriate power level to keep the
cooked food hot.
To activate it, select the plate, and press
on the CHEF sensor
led (15) located on the icon
up. Once the function is activated, the
symbol will appear on the power
indicator (3).
You can override the function at any
the power level or by choosing a
DERRETIR FUNCTION (depending
on the model)
This function maintains a low
temperature in the cooking zone.
Ideal for defrosting food or for slowly
melting other food types as chocolate,
butter, etc.
To activate it, select the plate, and press
on the CHEF sensor
led (16) located on the icon
up. Once the function is activated, the
symbol will appear on the power
indicator (3).
You can override the function at any
the power level or by choosing a
36
F U E G O L E N T O F U N C T I O N
(depending on the model)
This feature allows you to keep
simmered.
After the food is boiled, enable the
plate by selecting it, and press the
CHEF sensor
located on the icon
the function is activated, the symbol
will appear on the power indicator (3).
You can override the function at any
the power level or by choosing a
HERVIDO FUNCTION (depending
on the model)
This function enables the automatic
boiling control, which is a great help for
cooking pasta, rice, eggs, boil some
food, etc. It is available only in zones
where the
Conditions of the container
(14) until the
lights
For a proper operation of the HERVIDO
function, you need to use a container
that meets the following preconditions:
- Bottom size as close as possible to
the diameter of the plate.
-WITHOUT CAP.
- Filled to over half its capacity at
room temperature water (never
use warmed or hot water).
Failure to comply with these conditions
will distort the proper control of boiling.
WARNING: do not use this
feature for a different cooking
purpose other than boiling water.
Never use oil, it may lead to overheat
(14) until the
lights
Activation of the function
To activate the function, select the plate,
and press the CHEF sensor
until the led (18) located on the icon
lights up.
(14) until the led (17)
lights up. Once
symbol appears.
(14)
Once the feature is activated, the
sign will appear on both the power
indicator (3) and the timer indicator
(12); a moving segment will appear,
indicating that the cooking is under
system's control.
When the system detects that it is about
Take this opportunity to prepare your
food for boiling or baking as desired.
After 30 seconds, a second beep will
be heard; if you have not already done
so, it's time to pour the food in the pan.
After the second beep, the system will
activate the timer and stopwatch for
you so that you can control how long
the food is to be boiled.
30 seconds after activating the
stopwatch, a third beep will sound
to warn that from that moment on,
the system will decrease the power
supplied in order to maintain a gentle
and continuous boil. The timer will
remain active until the end of cooking.
If desired, you can disable the timer
and set a time for the countdown and
automatic shutdown of the plate (see
section Timer Function).
Deactivation of the function
You can override the function at any
the power level or by choosing a
PARRILLA FUNCTION (depending
on the model)
This function sets an automatic power
control suitable for cooking on the grill.
To activate it, select the plate, and press
on the CHEF sensor (14) , until the
led (19) located on the icon
Once the function is activated, on the
power indicator (3) a moving segment
will appear indicating that the cooking
is in the preheating phase of the vessel.
will appear on the power indicator
(3) and a beep will be heard, indicating
to the user that he must add the food.
You can override the function at any
lights up.