Teka IZC 63632 MST Montageanleitung Und Empfehlungen Zur Verendung Und Wartung Seite 34

EN
the time automatically. The indicator
(3) relating to the timed hotplate
will alternately display the selected
power level and the symbol
Once the selected cooking time has
elapsed, the heating zone being timed
series of beeps for several seconds.
any sensor.The timer indicator (12)
the decimal dot (4) of the selected
hot, its power indicator (3) will display
alternately the H symbol and a "-".
If you wish to time another hotplate
at the same time, repeat steps 1 to 3.
If one or more zones are already
timed, the timer indicator (12) will
show by default the shortest remaining
related zone. Except when the "Paeller"
function is active, in which case it will
display by default the value of the
elapsed time of the corresponding
cooking phase. Rest of timed zones will
show on their corresponding indicator
zones the decimal dot blinking. When
cursor "slider" of another timed zone
is pressed, the timer will show the
remaining time of that zone for a few
seconds and its indicator will show
its power level and the "t" alternately.
Changing the programmed time.
For modifying programmed time,
cursor "slider" (2) of timed zone has
to be pressed. Then it will be possible
to read and modify the time.
Through sensors (10) and
you can modify the programmed time.
Disconnecting the clock
If you wish to stop the clock before the
programmed time is up, this can be
done at any time by simply adjusting
its value to '--'.
1 Select the desired plate.
2 Adjust the value of the clock to "00"
by using the sensor
clock is cancelled. This can also be
done more quickly by pushing the
34
"sensors
same time.
Power Management function
,.
(depending on model)
Some models are equipped with a
power limiting function (Power
Management). This function allows the
total power generated by the hob to be
having connected the hob to the power
supply, it is possible to access the power
limiting menu.
1 Press the
seconds. The letter PL will appear on
the timer indicator (12)
2 Press the locking touch key
the hob can be limited will appear and
these can be changed using the
(11) and
3 Once the value has been selected,
once again press the locking touch
key (6). The hob will be limited to
the chosen power value.
If you want to change the value again,
you must unplug the hob and plug it in
again after a few seconds. Thus you
will again be able to enter the power
limiting menu.
Every time the power level of a hotplate
is changed, the power limiter will
calculate the total power the hob is
generating. If you have reached the total
power limit, the touch control will not
allow you to increase the power level of
(11),
that hotplate. The hob will beep and the
power indicator (3) will blink at the level
that cannot be exceeded. If you wish to
exceed that value, you must lower the
power of the other hotplates. Sometimes
it will not be enough to lower another
by a single level as this depends on the
power of each hotplate and the level it is
set at. It is possible that to raise the level
of a large hotplate that of several smaller
ones must be turned down.
If you use the quick switch-on at
(10). The
maximum power function and the said
value is above the value set by the limit,
the hotplate will be set to the maximum
(10) and (11) at the
(11) touch key for three
(6).
(10) sensors.
possible level. The hob will beep and
the said power value will blink twice on
the indicator (3).
PAELLER function
This function allows you to cook a
"paella" step by step. Each cooking
an excellent result.
This function is only available in the
32 cm cooking zone and is operated
function starts operating, it deactivates
any power level that this zone may have
been assigned to.
To obtain a suitable result you must
use a paella pan of 40 cm (32 cm
of diameter at the base, see fig. 7)
with encapsulated iron bottom (type
cannot be assured, if another type of
paella pan is used. To achieve a perfect
result we recommend the use of our
container with code 118310021 (more
information in the QR code).
Fig.8
Fig.7
OPERATION
Place the pan well centered on the
cooking zone, add the oil and press
the sensor (23) to start cooking.
The symbol appears on the power