Mitsubishi Heavy Industries Mr. SLIMPSA-M KA-Serie Installationshandbuch Seite 16

6. Electrical work
en
14
Clock display
Clock Yes /No
12h disp. 12h/24h
AM/PM disp. AM12:00/ 12:00AM
Select:
Cursor Cursor
Display details 1/2
Clock Yes AM12:00
Temperature °C/°F/1°C
Room temp. Yes /No
Auto mode Yes /No
Backlight 30sec
Select:
Cursor Cursor
Display details
LED lighting Yes / No
Select:
Cursor Cursor
Contrast • Brightness
Brightness Lo/Mid/Hi
Light Dark
Main menu:
Low High Light Dark
[1] Clock display
[Button operation]
1 Select "Clock" from the display details setting screen, and press the F4 button
(Change) to bring up the clock display setting screen.
2 Use the F1 through F4 buttons to select "Yes" (display) or "No" (nondisplay) and
its format for the Status display and the Main display.
3 Save the settings with the SELECT button. (The factory settings are "Yes" (display)
and "12 h" format.)
Clock display:
Yes (Time is displayed on the Status display and the Main display.)
No (Time is not displayed on the Status display and the Main display.)
Display format:
24-hour format
12-hour format
AM/PM display (Effective when the display format is 12-hour):
AM/PM before the time
AM/PM after the time
Note:
Time display format will also be reflected on the timer and schedule setting display.
The time is displayed as shown below.
12-hour format: AM12:00 ~ AM1:00 ~ PM12:00 ~ PM1:00 ~ PM11:59
24-hour format: 0:00 ~ 1:00 ~ 12:00 ~ 13:00 ~ 23:59
[2] Temperature unit setting
[Button operation]
Move the cursor to "Temperature" from the display details setting screen, and select
the desired temperature unit with the F3 or F4 button. (The factory setting is Cen-
tigrade (ºC).)
• ºC: Temperature is displayed in Centigrade. Temperature is displayed in 0.5- or
1-degree increments, depending on the model of indoor units.
• ºF: Temperature is displayed in Fahrenheit.
• 1 ºC: Temperature is displayed in Centigrade in 1-degree increments.
[3] Room temperature display
[Button operation]
Move the cursor to "Room temp." on the display details setting screen, and select the
desired setting with the F3 or F4 button.
(The factory setting is "Yes".)
• Yes: Room temperature appears on the Main display.
• No: Room temperature does not appear on the Main display.
Note:
Even when "Yes" is set, the room temperature is not displayed on the Main display
in the "Basic" mode.
[4] Auto (single set point) mode display setting
[Button operation]
Move the cursor to "Auto mode" from the display details setting screen, and select the
desired mode with the F3 or F4 button. (The factory setting is "Yes.")
• Yes: "Auto Cool" or "Auto Heat" is displayed during operation in the Auto (single set
point) mode.
• No: Only "Auto" is displayed during operation in the Auto (single set point) mode.
[5] Backlight
The backlight lighting-up time can be set.
[Button operation]
Move the cursor to "Backlight" from the display details setting screen, and select
the desired time (5/10/20/30/60 seconds) with the F4 button. (The factory setting is
"30" seconds.)
Note:
This setting is effective on the Status display and the Main display.
[6] LED lighting
The LED lighting can be set to either "Yes" (On) or "No" (Off). (The factory setting
is "Yes".)
When "No" is selected, the LED will not light up even during the normal operation.
(4) Contrast•Brightness
[Button operation]
Select the desired brightness for the controller LCD with the F1 and F2 buttons.
Adjust the contrast with the F3 or F4 button. The current level is indicated with a
triangle.
Note:
Adjust the contrast and brightness to improve viewing in different lighting conditions
or installation locations. This setting can not improve viewing from all directions.