GGMgastro GSH360 Bedienungs- Und Wartungsanleitung Seite 12

WARNINGS FOR THE OPERATOR
- Before commissioning the machine, the operator must
have carefully read this publication and acquired in-depth
EN
knowledge of the technical specifications and the machine
controls.
- Before installing the machine, check that the installation site
is compatible with its overall dimensions.
- If the machine is "recessed", make sure that the com-
partment and adjacent furnishing elements are suitable,
namely that they do not suffer from being exposed to
the water vapour which can escape the machine during
operation and especially when the door opens after a
wash cycle.
- When installing or removing part of the machine, use only
suitable lifting and handling equipment for its weight.
- Do not allow unauthorised and unqualified personnel to
start, adjust, run or repair the machine.
Furthermore, refer to this manual for the necessary ope-
rations.
- The mechanical parts and the electric/electronic compo-
nents inside the machine are protected by fully closed
panels.
- Before cleaning and/or servicing the machine, make
sure that the main switch is set to "OFF" O, in order to
disconnect power from the machine while the operator is
intervening.
- The electric power system must be provided with an auto-
matic triggering device upstream of the main switch of the
machine and a suitable earthing system which complies
with all the requirements of industrial accident-prevention
standards.
- If the need arises to intervene on the main switch or in its
vicinity, disconnect the power to the line which the main
switch is connected to.
- All inspections and maintenance operations which require
the safety guards to be removed must be carried out under
the full responsibility of the user.
It is therefore recommended that only specialised and
authorised technical personnel perform these operations.
- Check that all the accident prevention safety devices (barri-
ers, guards, casings, microswitches, etc.) are not tampered
with and are in perfect working order before operation. If
not, have them repaired.
- Do not remove the safety devices.
- To avoid personal risks, use only electrical tools which are
correctly connected to the earth socket and compliant with
national safety regulations.
- Do not tamper with the electrical system or with any other
mechanism for any reason whatsoever.
- Wear safety gloves during machine cleaning.
- Never use your hands or unsuitable instruments to locate
leaks from the various hoses. Pressurised or irritating air
and fluids could cause serious harm to persons and/or
objects.
- Do not use your hands instead of suitable tools to operate
the machine
- Do not stop moving parts with your hands or other objects
12
SPECIAL
- PAY THE UTMOST ATTENTION TO THE RATING PLA-
TES ON THE MACHINE WHENEVER OPERATING ON
IT OR IN ITS VICINITY.
- The user must keep all the rating plates legible.
- Do not climb onto the door or on top of the machine.
- The user must also replace all rating plates which for any
reason have deteriorated or are not clearly visible, reques-
ting new ones from the Spare Parts Service.
- In case of machine malfunctioning or damage to its compo-
nents, contact the maintenance manager without performing
any further repairs.
- It is strictly prohibited for anyone to use the machine for
purposes other than those specifically intended and docu-
mented.
The machine must always be used in the ways, times and
places foreseen by good practice standards, by current laws
in every country, even though the specific country may not
have appropriate standards that regulate the sector.
- The manufacturer will not be held liable for accidents
or harm to persons or objects resulting from failure to
comply with the safety requirements and standards
indicated herein.
- These requirements, together with standards relative
to machine installation and to electrical connections,
constitute an integral part of the Industrial Accident
Prevention Regulations of each individual country.
- THESE SAFETY STANDARDS INTEGRATE AND DO NOT
REPLACE LOCAL SAFETY STANDARDS IN FORCE
- NEVER have rushed or makeshift repairs carried out
which could jeopardise proper machine operation.
- WHEN IN DOUBT, ALWAYS REQUEST THE INTERVEN-
TION OF SPECIALISED PERSONNEL.
- ANY TAMPERING BY THE USER RELIEVES THE
MANUFACTURER FROM ALL LIABILITY AND MAKES
THE USER SOLELY RESPONSIBLE FOR RESPOND-
ING TO THE COMPETENT ACCIDENT PREVENTION
AUTHORITIES.
- This appliance is not intended to be used by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
- Make sure that children do not play with the appliance.
- It is prohibited to spray water on the appliance to clean
it.