Remaining Hazards; Attachment And Operation - Scheppach 5901504901 Original Bedienungsanleitung

7.

Remaining hazards

The machine has been built using modern technology
in accordance with recognized safety rules. Some re-
maining hazards, however, may still exist.
• Risk of injury for fingers and hands by the rotat-
ing saw band due to improper handling of the work
piece.
• Risk of injury through the hurling work piece due
to improper handling, such as working without the
push stick.
• Risk of damaging your health due to wood dust and
wood chips. Wear personal protective cloth such as
goggles. Use a fitting dust extractor.
• Risk of injury due to defective saw band. Regularely
check saw band for such defects.
• Risk of injury for fingers and hands while changing
saw band. Wear proper gloves.
• Risk of injury due to starting saw band while switch-
ing on the machine.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
• Danger to health from running saw band due to long
hair and loose clothing. Wear personal protective
equipment such as a hair net and close-fitting work
clothing.
• The rollers can continue to rotate if a drive belt or
a saw blade breaks. Always wait for the machine to
come to a complete stop before opening the sep-
arating guards.
• Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by follow-
ing the instructions in „General safety instructions"
„Proper Use" and in the entire operating manual.

8. Attachment and operation

Before starting the equipment
Make sure the machine stands securely, i.e. bolt it to a
workbench or solid base. There are two holes for this
purpose in the machine foot. (Fig. 18+19)
• The saw table must be mounted correctly.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
• Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
• Before you connect the machine to the power sup-
ply, make sure the data on the rating plate is the
same as that for your mains.
Assembly tools
1 engineer's wrench SW 10/13
1 hexagonal head spanner SW 3
1 hexagonal head spanner SW 4
Tabletop and the mounting angles are not mounted for
reasons of packaging technology.
8.1 Installation of the Underframe, Fig. 3+4
1. Put a wooden block behind the machine, and than
carefully turn over the machine so that the base
plate lies on the floor.
2. Loosely screw the frame feet with 12 screws (M6 x
12) to the base plate.
3. Insert the intermediate bottom, and loosely screw
in 8 screws (M6 x 12) to fasten it.
4. Put the feet caps onto the frame feet.
5. Screw the mounting plates (1) for the handle (2) on
the bottom of the base plate.
6. Place the first plate at the outer edge, the second
one at the first frame.
7. Turn the machine upright again, align it and tighten
all screws.
8. Screw the wheel clips (3) on the left side of the
base onto the base feet, and hand-tight the screws.
9. Tighten the screws of the wheel clips.
10. Push the transport handle into the mounting plates,
turn the handle until it is pushed in completely.
11. During the transport, pull out the handle only until
the rear screw sits close to the second mounting
plate.
12. The transport is only admissible on straight, even
surfaces.
Caution! In case of an oblique position of the machine
it may turn over.
8.2 Installation of the tabletop, Fig. 5
1. Open the housing door (1) by opening the top door
lock (2.1) and unscrewing the bottom door lock
(2.2) anti-clockwise.
2. Move swivel segment to 0°.
3. Loosely screw the tabletop.
4 hexagon head cap screws M 8 x 16
4 serrated lock washers
www.scheppach.com
A 8,4
GB | 33