Service Information; Storage; Electrical Connection - Dexter 3901324953 Originalbetriebsanleitung

15.4.1 Removing the saw blade guard (fig. 11)
1. Move the quick release button (5b) in the guide
so that the thinner part of the quick release button
(5b) is exposed in the opening.
2. Carefully slide the saw blade guard (5) over the
riving knife (4).
15.4.2 Removing the table inlay (fig. 9)
1. Loosen the countersunk head screw (6a).
2. Remove the table inlay (6) from the saw table.
15.4.3 Removing the saw blade guard (fig. 23 + 24)
PREREQUISITE: The saw blade (3) has been set to
the maximum cutting depth (see 10.2).
1. Place the open-ended spanner 22 mm (37) on the
outer saw blade flange (3b) and secure the drive
shaft (3c) in this way.
2. Turn the fixing nut (3d) counterclockwise with the
open-ended spanner 22 mm (37) to undo the fix-
ing nut (3d).
3. Hold the saw blade (3) carefully with one hand
4. Remove the fixing nut (3d) and outer saw blade
flange (3b) from the drive shaft (3c).
5. Now remove the saw blade (3) from the drive shaft
(3c) and carefully draw it up and out of the saw table.
ATTENTION!
There is a reducer ring (3e) on the shaft, which must
also be removed.
15.4.4 Fitting the saw blade (fig. 23 + 24)
1. Clean the external and internal saw blade flange
(3b/3a) carefully, before fitting a new saw blade
(3).
2. Clean the reducer ring (3e) and put it back in
place.
3. Place a new saw blade (3) on the drive shaft (3c).
Observe the rotational direction: The cutting an-
gle of the teeth must point in the running direction
(forwards). The running direction is usually also
marked on the saw blade.
4. Fit the outer saw blade flange (3b) back on the
drive shaft (3c). Ensure the correct alignment of
the outer saw blade flange (3b).
5. Screw the fixing nut (3d) tight onto the drive shaft
(3c) with the hand.
6. Carefully turn the saw blade (3) in the running
direction: It must be precisely centred and must
not "wobble". Check that the saw blade (3) and
outer saw blade flange (3b) are sitting correctly
and align the parts once more, if the saw blade is
not precisely centred.
m WARNING!
Warning against unexpected hazards and dam-
ages to the product
- Check the setting of the saw blade after every
saw blade replacement.
7. Hold the outer saw blade flange (3b) in position
with the open-ended spanner 22 mm (37) and
turn the fixing nut (3d) tight in a clockwise direc-
tion with the open-ended spanner 22 mm (37).
8. Mount the table inlay (6) and the saw blade guard
(5) (see 8.5.3 and 8.6.1).
9. Check the correct setting of the riving knife (see
8.5.2).

15.5 Service information

With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*:carbon brushes, table inlay, push
stick, saw blade
* may not be included in the scope of supply!

16. Storage

m WARNING!
Danger of injury due to unexpected start-up of the ma-
chine
- Remove the mains plug from the socket.
ATTENTION!
Product damage due to incorrect storage
- Store the product protected against dirt, dust and
moisture.
- Store the product in its original packaging.
1. Store the product in a dark, dry and frost-free
place that is inaccessible to unauthorised per-
sons.
2. The optimum storage temperature lies between 5
and 30 °C.
3. Store the operating manual with the product.

17. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions. The
customer's mains connection as well as the ex-
tension cables used must also comply with these
regulations.
17.1 Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors
• Kinks where the connection cable has been improp-
erly fastened or routed
GB | 43