Technical Data - Dexter 3901324953 Originalbetriebsanleitung

e) The table saw must be secured. A table saw that
is not properly secured may move or tip over.
f) Remove tools, wood scraps, etc. from the table
before the table saw is turned on. Distraction or
a potential jam can be dangerous.
g) Always use saw blades with correct size and
shape (diamond versus round) of arbour holes.
Saw blades that do not match the mounting hard-
ware of the saw will run off-centre, causing loss of
control.
h) Never use damaged or incorrect saw blade
mounting means such as flanges, saw blade
washers, bolts or nuts. These mounting means
were specially designed for your saw, for safe op-
eration and optimum performance.
i) Never stand on the table saw, do not use it as
a stepping stool. Serious injury could occur if the
tool is tipped or if the cutting tool is accidentally
contacted.
j) Make sure that the saw blade is installed to ro-
tate in the proper direction. Do not use grind-
ing wheels, wire brushes, or abrasive wheels
on a table saw. Improper saw blade installation or
use of accessories not recommended may cause
serious injury.
Safety instructions for the handling of saw blades
1. Only use insertion tools if you have mastered their
use.
2. Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
3. Observe the motor / saw blade direction of rota-
tion.
4. Do not use any insertion tools with cracks. Sort
out cracked insertion tools. Repairs are not per-
mitted.
5. Clean dirt, grease, oil and water off of the clamp-
ing surfaces.
6. Do not use any loose reducing rings or bushes to
reduce holes on circular saw blades.
7. Make sure that fixed reducer rings for securing
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
8. Make sure that fixed reducer rings are parallel to
each other.
9. Handle insertion tools with caution. They are ide-
ally stored in the originally package or special
containers. Wear protective gloves in order to im-
prove grip and to further reduce the risk of injury.
10. Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
11. Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12. Only use the supplied saw blade for cutting wood,
never for the processing of metals.
13. Use the correct saw blade for the material to be
processed.
14. Use only a saw blade with a diameter that match-
es the specifications on the saw.
15. Use only saw blades that are marked with an
equal or higher rotational speed than that marked
on the power tool.
16. Use only saw blades recommended by the manu-
facturer which conform to EN 847-1, if intended for
cutting wood or similar materials.
17. Wear suitable personal protective equipment,
such as:
- Hearing protection;
- Protective gloves when handling saw blades.
18. Only use saw blades recommended by the manu-
facturer which conform to EN 847-1. Warning!
When changing the saw blade, ensure that the
cutting width is not smaller and the width of the
saw blade disc is not greater than the thickness
of the riving knife!
19. When sawing wood and plastics, avoid the saw
teeth overheating. Reduce the feed speed in or-
der to avoid the plastic melting.
20. Please note that complex non-through cutting op-
erations and tapered cuts are not permitted.
21. Avoid bevel ripping on bevelling side of the saw
blade.
22. Make sure when mounting or when installing the
parallel stop that it should be aligned parallel to
the the saw blade.

6. Technical data

AC motor
Power consumption
5000 rpm
3200 rpm
Idle speed n
0
Gear 1
Gear 2
Carbide saw blade
Thickness of saw blade
disc
Number of teeth
Riving knife thickness
Min. size of workpiece W
x L x H
Table size
Left/right table width
extension
Cutting height max. 45 °
Cutting height max. 0 °
220 - 240 V~ 50 Hz
1800 W (S1*)
2200 W (S6 20 %**)
500 W (S1*)
3200 rpm
5000 rpm
ø 254 x ø 30 x 2.8 mm
1.8 mm
24
2.5 mm
10 x 50 x 1 mm
575 x 555 mm
575 x 225 mm
65 mm
85 mm
GB | 35