Operation - Scheppach ASP50-ES Original Bedienungsanleitung

• At the other end of the drain hose (11) there is a
stopper (7) which must be closed during suction op-
eration. The drain hose can also be fastened at the
drain hose holder (8). (Fig. 10)
Installing the foam filter (22) (fig. 3, 11)
Never use the device without filter! Always ensure that
the filters are correctly fitted!
• Installing the foam filter (22): For wet vacuuming,
slide the foam filter (22) provided over the filter bas-
ket with safety float valve (20).
Installing the folded filter (24) (fig. 3, 12)
For dry vacuuming, slide the folded filter (24) provided
over the filter basket with safety float valve (20). The
folded filter (24) is only suitable for dry vacuuming!
Installing the paper filter bag (23) (fig. 3, 13)
It is recommended to use an additional paper filter bag
(23) when vacuuming fine, dry dirt.
• Slide the paper filter bag (23) over the suction open-
ing in the stainless steel container (15). The paper
filter bag (23) is only suitable for dry vacuuming. The
paper filter bag (23) makes it easier to dispose of the
dust collected.
Installing the suction hose (21) (fig. 3, 14, 15)
Connect the suction hose (21) to the corresponding
port, depending on the desired use, on the wet and dry
vacuum.
Vacuuming:
Connect the suction hose (21) to the suction hose port
(16). To do so, slide the end of the suction hose (21)
with the two nipples into the suction hose port (16) (A).
Insert the two nipples into the recesses. Once the suc-
tion hose is fully inserted, turn it clockwise (B).
Blowing:
Connect the suction hose (21) to the blowing function
connection port (19). Slide the end of the suction hose
(21) with the two nipples into the blowing function con-
nection port (19). Insert the two nipples into the recess-
es. It is not necessary to turn it here.
Installing the metal extension tube (27), suction
hose (21) and nozzles (25/26) (fig. 16, 17)
• Connect the metal extension tube (27) with the bent
end of the suction hose (21).
• Fit the floor nozzle (25) or joint nozzle (26) to the
other end of the metal extension tube (27).
22 | GB
• Push the slide piece forwards (A) to change the
length of the metal extension tube (27). (Fig. 17)
• Pull the tube to the desired length (B). Ensure that
the slide lock latches into place. (Fig. 17)

8. Operation

m WARNING!
Switch the device off if liquid or foam emerges with the
exhaust air during wet vacuuming.
Switch on / switch off / automatic (fig. 18, 19)
The ON/OFF switch (18) has three settings:
1 switch setting 0: Off
2 switch setting II: On
• Press the on/off switch (18) to switch on.
• Press the on/off switch (18) again to switch the de-
vice off.
3 switch setting I: Automatic mode (the vacuum clean-
er will be switched on by an electric tool).
• Plug your electrical tool's cable into the automatic
socket (fig. 19).
• Connect the suction hose to the suction connection
on your electrical tool.
• Check that the connection is secure and airtight.
• Set the switch on the vacuum system to position "I"
= Automatic mode.
Dry vacuuming (fig. 3, 12, 13)
Use the folded filter (24) for dry vacuuming. The paper
filter bag (23) can be used in addition. This ensures that
the folded filter (24) remains free of dust for longer and
maintains the vacuum power for longer.
In addition, the disposal of the dust is also easier.
Always ensure that the filters are correctly fitted.
Wet vacuuming (fig. 3, 11)
Use the foam filter (22) for wet vacuuming. Ensure that
the foam filter (22) is correctly fitted.
If the stainless steel container (15) is full, the safety
float valve (20) closes the suction port and suction op-
eration is interrupted.
m IMPORTANT!
The device is not suitable for vacuuming flammable
liquids. For wet vacuuming, use the only the foam filter
(22) provided.
Drain hose (11) (fig. 20)
The stainless steel container (15) is equipped with a
water drain hose (11) in order to make it easier to drain.
www.scheppach.com