Operation - Scheppach ASP30-OES Originalbetriebsanleitung

Installing the castor mounts (fig. 4+5)
• Turn the stainless steel container (9) upside-down
(the machine head (2) must be removed).
• Push the castor mounts (5) into the cut-outs pro-
vided on the wheel mounting base (7). (4x)
• Fasten the castor mounts (5) with a screwdriver
(not included in the delivery) and one screw each
(22). (4x)
Installing the castors (6) (fig. 6)
• Press the four castors (6) into the holes in the wheel
mounting base (5).
Installing the machine head (2) and the handle (1)
(Fig. 7)
• Place the machine head (2) on the stainless steel
container (9). Secure the machine head (2) with
the locking hooks (4). When installing the machine
head (2), ensure that the locking hooks (4) latch into
place correctly.
• Place the handle (1) on the machine head (2) and
fasten it with two screws (22) with a screwdriver
(not included in the delivery).
Installing the foam filter (16) (fig. 3+8)
Never use the device without filter! Always ensure
that the filters are correctly fitted!
• Installing the foam filter (16): For wet vacuuming,
slide the foam filter (16) provided over the filter bas-
ket with safety float valve (14).
Installing the folded filter (18) (fig. 3+9)
For dry vacuuming, slide the folded filter (18) provided
over the filter basket with safety float valve (14). The
folded filter (18) is only suitable for dry vacuuming!
Installing the paper filter bag (17) (fig. 3+10)
It is recommended to use an additional paper filter
bag (17) when vacuuming fine, dry dirt.
• Slide the paper filter bag (17) over the suction open-
ing in the stainless steel container (9). The paper
filter bag (17) is only suitable for dry vacuuming.
The paper filter bag (17) makes it easier to dispose
of the dust collected.
Installing the suction hose (15) (fig. 3+11+12)
Connect the suction hose (15) to the corresponding
port, depending on the desired use, on the wet and
dry vacuum.
Vacuuming:
Connect the suction hose (15) to the suction hose port
(10). To do so, slide the end of the suction hose (15)
with the two nipples into the suction hose port (10)
(A). Insert the two nipples into the recesses. Once
the suction hose is fully inserted, turn it clockwise (B).
Blowing:
Connect the suction hose (15) to the blowing func-
tion connection port (13). Slide the end of the suction
hose (15) with the two nipples into the blowing func-
tion connection port (13). Insert the two nipples into
the recesses. It is not necessary to turn it here.
16 І 60
Installing the metal extension tube (21), suction
hose (15) and nozzles (19/20) (fig. 13)
• Connect the metal extension tube (21) with the bent
end of the suction hose (15).
• Fit the floor nozzle (19) or joint nozzle (20) to the
other end of the metal extension tube (21).
• Push the slide piece forwards (A) to change the
length of the metal extension tube (21). (Fig. 14)
• Pull the tube to the desired length (B). Ensure that
the slide lock latches into place. (Fig. 14)
Installing the bottom cable holder (fig. 3+15)
• Clip the bottom cable holder (23) onto the wheel
mounting base (7) at the rear of the device. The
top cable holder (12) is on the connection port for
the blower function (13).

8. Operation

m WARNING!
Switch the device off if liquid or foam emerges with
the exhaust air during wet vacuuming.
Switching on/off (fig. 16)
The on/off switch (11) has two settings
• Switch setting 0: Off
• Switch setting I: On
Press the on/off switch (11) to switch on. Switch set-
ting I: On
Press the on/off switch (11) again to switch the device
off. Switch setting 0: Off
Dry vacuuming (fig. 3+9+10)
Use the folded filter (18) for dry vacuuming. The pa-
per filter bag (17) can be used in addition. This en-
sures that the folded filter (18) remains free of dust for
longer and maintains the vacuum power for longer.
In addition, the disposal of the dust is also easier.
Always ensure that the filters are correctly fitted.
Wet vacuuming (fig. 3+8)
Use the foam filter (16) for wet vacuuming. Ensure
that the foam filter (16) is correctly fitted.
If the stainless steel container (9) is full, the safety
float valve (14) closes the suction port and suction
operation is interrupted.
m IMPORTANT!
The device is not suitable for vacuuming flammable
liquids. For wet vacuuming, use the only the foam filter
(16) provided.
Water drain plug (8) (fig. 17)
The stainless steel container (9) is equipped with a
water drain plug (8) in order to make it easier to drain.
Open the water drain plug (8) by turning it counter-
clockwise and drain out the liquid.