Hauff-Technik HSD-Serie Montageanleitung Seite 6

Ringraumdichtung
HSD
Beschädigung durch unsachgemäße Lagerung!
Bei unsachgemäßer Lagerung können Sachschäden in erheblicher Höhe ent-
stehen.
• Ringraumdichtung sowie Abdichtset vor der Montage vor Beschädigungen,
Feuchte und Verunreinigungen schützen. Es dürfen nur unbeschädigte Teile
montiert werden.
• Die Lagerung der Ringraumdichtung sowie des Abdichtsets muss so erfolgen,
dass dieser keinen zu niederen Temperaturen (<5 °C) und höheren Temperatu-
ren (>30 °C) sowie keiner direkten Sonneneinstrahlung ausgesetzt ist.
Entsorgung
Sofern keine Rücknahme- oder Entsorgungsvereinbarung getroffen wurde, zer-
legte Bestandteile nach sachgerechter Demontage der Wiederverwertung zufüh-
ren:
• Metallische Materialreste nach den geltenden Umweltvorschriften verschrotten.
• Elastomere nach den geltenden Umweltvorschriften entsorgen.
• Kunststoffe nach den geltenden Umweltvorschriften entsorgen.
• Verpackungsmaterial nach den geltenden Umweltvorschriften entsorgen.
EN Safety Instructions and Information
Target Group
The installation may only be carried out by technical experts.
Qualified and trained individuals carrying out installation must have
• knowledge of general safety and accident prevention regulations as amended,
• knowledge of how to use safety equipment,
• knowledge of how to use hand tools and electric tools,
• knowledge of the relevant standards and guidelines for laying pipes/cables and
for backfilling utility trenches as amended,
• knowledge of the regulations and installation guidelines of the supply company
as amended,
• knowledge of the waterproof concrete directive and building waterproofing
standards as amended.
General information and intended use
In line with their intended use, our products have been developed solely for instal-
lation in buildings made of state-of-the-art materials. Insofar as no express written
confirmation has been provided by us, we do not accept any liability for any other
purposes or purposes going beyond the above.
For warranty conditions, please see our current General Terms and Delivery Condi-
tions. We explicitly draw your attention to the fact that no warranty whatsoever
applies for any subsequent damage occurring as a result of failure to follow the
installation instructions or if our products are used incorrectly or combined with
third-party products.
The Press seal is designed for sealing pipes to be newly installed in core drill holes
or pipe sleeves. The Press seals HSD are suitable for the installation and insertion
of 1 pipe with outer diameter 32 - 450 mm.
HSD press seals are tested by FHRK according to current test guidelines and
bear the seal "FHRK Quality".
The WRD sealing set allows corrugated cable ducts, as well as local and district
heating pipes, to be fed into buildings through walls in a pressurized water-tight
manner. The patented ring clips in the corrugated section prevent deformations
and damage to the corrugated pipe and at the same time keep the closing pres-
sure of the press seal uniform and constant. The insulation ring included in the
scope of supply centres the corrugated pipe on the inside of the building and
neatly finishes the wall connection.
Safety
This section provides an overview of all the main safety aspects for optimum pro-
tection of personnel and a safe installation process.
If there is a failure to observe the instructions and safety information set out here,
this may result in significant hazards.
Press seal assembly and sealing set assembly must comply with the relevant pro-
fessional association regulations, VDE provisions, national safety and accident pre-
vention regulations as well as company regulations (work and procedural instruc-
tions).
The fitter must wear the relevant protective clothing.
Only intact components may be installed.
The following instructions are to be observed prior to as-
sembly of the press seal and the sealing set:
WARNING!
Risk of injury in the event of improper installation!
Improper installation can result in significant bodily harm and property da-
mage.
• Seal the underground and cable substructure well prior to laying pipes or cables
so that the latter cannot subside.
6
• Observe the nationally applicable laying and filling regulations for pipes and
cables.
NOTICE!
No sealing due to incorrect installation!
Improper installation can result in damage.
• For the one-sided installation of the press seal and the sealing set WRD into the
core drilling, carry out the sealing on the outside of building.
• If installed correctly, retightening the screws is not necessary.
• Any anticipated reductions must be compensated for by the installation of cen-
tering guides in the conduits or core drillings and/or by spacers.
• The HSD type (20 mm sealing width) must always be secured so that it cannot
fall/slide out
• The HSD press seals have to be secured to ensure they do not slide out when
permanently exposed to dynamic pressure
• Prior to installing the press seal or rather the sealing set WRD any existing
breaks or blowholes in the cored hole have to be repaired.
• If the Press seal is installed in an exposed duct, then the duct wall must be sta-
bilised with a clamping strap at the location of the Press seal.
• Ensure that the medium pipe is centred and horizontal in the core drilling/wall
sleeve.
• Do not lubricate the outer sealing surface of the Press seal with lubrication. The
outer sealing surface of the press seal with must be free from grease and dry.
• If sealing is to be carried out on the outside of the building, a check must be
carried out before the trench is filled and all laying and connection work is
completed to see whether the rubber in all inspection openings can be seen
and felt. If this is not the case, or it is no longer possible to access the inspec-
tion openings, the torque must be checked and if necessary tightened.
• If sealing is to be carried out on the inside of the building, a check must be car-
ried out after the trench has been filled and all laying and connection work is
completed to see whether the rubber in all inspection openings can be seen
and felt. If this is not the case, or it is no longer possible to access the inspec-
tion openings, the torque must be checked and if necessary tightened.
• Do not use cleaning agents containing solvents to clean the Press seal. We
recommend using the cable cleaner KRMTX.
• For details of other accessories and further information, see www.hauff-tech-
nik.de and the technical data sheets as well as the safety data sheet.
Personnel requirements
Qualifications
WARNING!
Risk of injury in case of inadequate qualification!
Improper handling can result in significant bodily harm and property da-
mage.
• Installation may only be carried out by qualified and trained individuals who
have read and understood these instructions.
Skilled experts
Based on their specialist training, skills, experience and familiarity with the rele-
vant provisions, standards and regulations, skilled experts are able to carry out the
work assigned, independently identifying and avoiding potential hazards.
Transport, packaging, scope of delivery and storage
Safety instructions in connection with transport
NOTICE!
Damage in the event of improper transport!
Significant damage can occur in the event of improper transport.
• When unloading packaging items on delivery and in the course of in-house
transport, proceed with care and observe the symbols on the packaging.
Transport inspection
Inspect the delivery immediately on receipt for completeness and transport da-
mage. In the event of transport damage being visible from the outside, proceed as
follows:
• Do not accept the delivery or only do so subject to reservations.
• Make a note of the extent of damage in the transport documentation or de-
livery note provided by the transporter.
• Submit a claim for every defect as soon as it has been identified.
• Claims for damages can only be asserted within the applicable claim
period.
Delivery scope
The scope of delivery of the Press seal HSD includes:
• 1 Press seal HSD
The scope of delivery for the WRD sealing set includes:
Art. Nr.: 5090032098 Rev.: 01/2022-11-14