Inhaltsverzeichnis
Werbung
•
Work in a well-ventilated area
•
Work with approved safety equipment, such as
those dust masks that are specially designated to
filter out microscopic particles.
The operation of any circular saw can result in
foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool
operation, always wear safety goggles or safety glasses with
side shield and a full-face shield when needed.
4. KNOW YOUR TWINCUTTER
SAW
Your Twincutter Saw has many built-in convenience
features for fast, efficient cutting. These features include
an innovative Two Saw Blade System where the blades
spin in opposite directions to provide smooth, clean cuts
with less vibration and kickback. It also includes a pre-
installed blade lubricating system for cutting Aluminium,
copper, stainless steel and cast iron.
For your convenience, there is no special assembly
required for your Twincutter Saw except assist handle.
For specification refer to DATA SHEET.
5. OPERATING INSTRUCTIONS
SAW BLADES
Even the best saw blades would not cut efficiently if they
are not kept clean, sharp and properly set. Using a dull
blade will place a heavy load on your saw and increases
the danger of kickback. Keep extra blades on hand, so
sharp blades are always available.
Gum and wood pitch hardened on your blade will slow
your saw down. Use gum and pitch remover, hot water
or kerosene to remove these accumulations. Do not use
gasoline.
This Twin Cutter saw uses specially designed
blades and no other types of blades should ever be
used. Other blades will not operate safely in this saw and
could result in serious personal injury.
BLADE GUARD SYSTEM
The lower blade guard, attached to your saw, is there for
your protection and safety. It should never be altered
for any reason. If it becomes damaged or begins to
return slowly or sluggishly, Do not operate your saw
until the damage has been repaired or replaced. Always
leave the guard in its correct operating position when
using the saw.
When sawing through a workpiece, the lower blade
guard does not cover the blade on the underside of
the workpiece. Since the blade is exposed on the underside of
the workpiece, Always keep your hands and fingers away from
the cutting area. Any part of your body coming in contact with
the moving blade will result in serious injury.
Never use the saw when the guard is not operating
properly. The guard should be checked for correct
operation before each use. If you drop your saw, check the lower
blade guard and bumper for damage at all depth setting before
8
using. NOTE: The guard is operating properly when it moves
freely and then readily returns to the closed position. If, for any
reason, your lower blade guard does not close freely, take it to
your nearest authorized Repair Center for service before using it.
STARTING A CUT
1. Always use your saw correctly.
2. Always support the workpiece near the cut.
3. Always support the workpiece so the cut will be on
your side.
4. Always clamp the workpiece so it will not move
during the cut. Before starting a cut, draw a guideline
along the desired line of cut. Then place the front
edge of the saw blades on that part of the workpiece
that is solidly supported.
5. Never place the saw on the part of the workpiece
that will fall off when the cut is made.
6. Always keep the cord away from the cutting area.
Always place the cord so it does not hang up on the
workpiece when making a cut.
Always maintain control of the saw to make sawing
safer and easier. Loss of control of the saw could
cause an accident resulting in possible serious injury
If the cord hangs up on the workpiece during a cut,
release the trigger switch immediately. Unplug the
saw and move the cord to prevent it from hanging up again.
Using the saw with a damaged cord could result in
serious injury or death. If the cord has been
damaged, have it replaced before using the saw again.
7. Slide the on/off switch to start the saw. Always let the
blades reach full speed before you begin to cut into
the workpiece.
If the blades come in contact with the workpiece
before they reach full speed, it could cause the saw
to kickback towards you, resulting in serious injury
8. When making a cut, always use steady, even
pressure. Forcing the saw causes rough cuts and
could shorten the life of the saw or cause kickback.
When sawing through a workpiece, the lower
blade guard does not cover the blades. The blades
are exposed on the underside of the workpiece; always keep
your hands and fingers away from the cutting area. Any part
of your body coming in contact with the moving blade will
result in serious injury.
Whenever you lift your saw from the workpiece,
the blade is exposed on the under side of the saw
until the lower blade guard closes. always MAKE SURE that
the lower blade guard is closed before setting the saw down
on work surface.
9. Always use the lubricating device (included) when cutting
Aluminium, Copper, Stainless Steel & Cast Iron materials,
because they have a tendency to smear and adhere to the
blades.
10. Alwas Feeding must be parallel to the blade. Feeding at
an angle can burn the blade and damage the blade teeth.
,
,
.
.
,
. .
,
.
,
,
,
,
,
.
.
,
,
.
,
3
.
.
.
Ferm
Ferm
.
1.
•
,
,
•
•
2.
•
,
•
.
•
,
•
,
3.
.
•
•
•
.
,
•
.
•
.
4.
,
•
•
•
,
•
•
•
.
,
,
.
.
-
.
,
.
"
"
"
"
,
69
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
