Additional Safety Instructions - Ferm MSM1034 Originalbetriebsanleitung

• Wear gloves when you exchange the saw
blade or when rough material is to be sawn. It
is best to keep saw blades in a separate
holder to prevent anyone getting hurt.
• When the machine is equipped with a laser,
this may not be replaced by a different type of
laser. Repairs may only be carried out by the
laser manufacturer or a recognised specialist.
• The operator should wear ear protectors to
reduce any damage to hearing.
• To prevent accidents occurring by the
accidental switching on of the machine, the
plug must always be pulled out of the socket
before adjustment of the stop or the saw head
is carried out, when changing blades or
accessories, and when maintaining the
machine.
• To prevent electric shocks, when plugging the
plug into the socket the metal pins must not be
touched in any way whatsoever.
• Never use the cord to pull the plug out of the
socket. Keep the cord away from oil, heat and
sharp objects.
• Never apply a cleaning or lubrication agent to
a saw blade that is still revolving.
• To prevent fires, never use the machine in the
vicinity of flammable liquids, vapours or gases.
• Always use original accessories: others may
cause wounding.
• Always choose the right saw blade in relation
to the material to be sawn.
• Ensure that during operation, the swinging
guard functions properly. It must move freely
and be able to close by itself. It should never
be jammed in the open position.
• Do not work with material containing asbestos.
• Protect the saw blade from strikes and shocks.
Do not apply side pressure to the saw blade.

Additional safety instructions

1. When using the saw blades with hard metal
teeth (Carbon tipped) it is advisable to use
blades with a negative or slightly positive
cutting angle. Do not use any saw blades with
deeply cut teeth. They can grip the protective
cap.
2. Attention: First carefully assemble all the parts
before starting work. Follow the procedure as
indicated.
3. If you are not familiar with using such a
machine, you would be better to be informed
first by a professional, an instructor or by a
technician.
4. Always clamp or press the workpiece firmly
Ferm
against the saw guide, before you carry out
the process. The use of all possible clamping
set-ups is preferable to using your hands.
5. Important: If you are holding the workpiece by
hand for the process to be carried out, keep a
minimum distance of 100 mm from the saw
blade.
6. Always press the workpiece against the
bench.
7. Keep the saw blade sharp and check regularly
whether it rotates freely without abnormal
vibrations. Replace the saw blade if
necessary.
8. Allow the machine to rotate freely until it
reaches the maximum number of revolutions,
before you start the process.
9. Maintain the air inlets at the back and the
bottom of the bench saw machine and electric
engine for a longer machine life. Dust piles
must be removed.
10. Always lock the different degree set-ups
before you start processing.
11. Only buy suitable saw blades with a number of
revolutions of at least 4500 revolutions per
minute.
12. Only use the correct saw blade. Too small or
too big saw blades are extremely dangerous.
13. Regularly inspect the saw blade for any faults.
Replace the saw blade if necessary.
14. Grease the new saw blade and clean the
flanges before you assemble the new blade.
Then assemble the blade in the correct
direction and pull the flanges firmly using the
central bolt.
15. Only use original flanges. All other types are
not suitable.
16. Never work without the protective cap of the
saw blade.
17. The moving part of the protective cap must
also remain assembled.
18. Never grease the saw blade while it is rotating.
19. Always keep your hands removed from the
track of the saw blades.
20. Never pick up the workpiece by grasping with
your hands along or behind the saw blade.
21. Ensure that the workpiece never touches the
saw blade before the machine has been
switched on.
22. Never process metal or stone sorts with this
machine.
23. Use support aids in order to support long
workpieces.
24. Never use the machine in a dangerous
environment, where inflammable gases or
EN
7