Additional Safety Instructions - Ferm TSM1033 Originalbetriebsanleitung

Additional safety instructions

1. When using the saw blades with hard metal
teeth (Carbon tipped) it is advisable to use
blades with a negative or slightly positive cutting
angle. Do not use any saw blades with deeply
cut teeth. They can grip the protective cap.
2. Attention: First carefully assemble all the parts
before starting work. Follow the procedure as
indicated.
3. If you are not familiar with using such a machine,
you would be better to be informed first by a
professional, an instructor or by a technician.
4. Always clamp or press the workpiece firmly
against the saw guide, before you carry out the
process. The use of all possible clamping set-
ups is preferable to using your hands.
5. Important: If you are holding the workpiece by
hand for the process to be carried out, keep
a minimum distance of 100 mm from the saw
blade.
6. Always press the workpiece against the bench.
7. Keep the saw blade sharp and check regularly
whether it rotates freely without abnormal
vibrations. Replace the saw blade if necessary.
8. Allow the machine to rotate freely until it
reaches the maximum number of revolutions,
before you start the process.
9. Maintain the air inlets at the back and the
bottom of the bench saw machine and electric
motor for a longer machine life. Dust piles
must be removed.
10. Always lock the different degree set-ups
before you start processing.
11. Only buy suitable saw blades with a number
of revolutions of at least 6000 revolutions per
minute.
12. Only use the correct saw blade. Too small or
too big saw blades are extremely dangerous.
13. Regularly inspect the saw blade for any faults.
Replace the saw blade if necessary.
14. Grease the new saw blade and clean the
flanges before you assemble the new blade.
Then assemble the blade in the correct
direction and pull the flanges firmly using the
central bolt.
15. Only use original flanges. All other types are
not suitable.
16. Never work without the protective cap of the
saw blade.
17. The moving part of the protective cap must
also remain assembled.
8
18. Never grease the saw blade while it is rotating.
19. Always keep your hands removed from the
track of the saw blades.
20. Never pick up the workpiece by grasping with
your hands along or behind the saw blade.
21. Ensure that the workpiece never touches
the saw blade before the machine has been
switched on.
22. Never process metal or stone sorts with this
machine.
23. Use support aids in order to support long
workpieces.
24. Never use the machine in a dangerous
environment, where inflammable gases or
fluids are present.
25. Never leave the machine unattended without
first disconnecting it from the mains voltage.
26. If you hear abnormal noises, try to trace them
or take the machine to a recognized fitter, or
repair company.
27. If a part is broken or damaged, replace it or
repair it immediately.
28. Never stand in the track of the saw blade but
stand to the left or the right of the saw bench.
29. Your hands must likewise be placed next to
the track of the saw blade.
30. Always use the push stick instead of your
hands to push the wood through the saw.
31. Always place the wood at the front of the saw
bench and then push it further back.
32. For mitring only the adjustable guide must be
used and the fence must be removed. (Fig. J)
33. Never use the fence as a linear measure for
cutting off beams.
34. If the saw blade is locked: first switch off the
machine before you attend to the fault.
35. Avoid workpieces hitting back in your direction
by taking the following measures:
• Always use sharp saw blades.
• Do not saw too small workpieces.
• Never release the workpiece before it has
been completely pushed through the saw.
• Always adjust the guide parallel to the saw
blade.
• Never remove the saw protection.
36. Before you continue sawing, ensure that you
are standing firmly and that your hands are in
the required position.
37. Never use thinners to clean the machine. Only
use a damp cloth for cleaning.
38. Do not use saw blades which are damaged or