Ferm JSM1018 Gebrauchsanweisung Seite 8

GB
3. ASSEMBLY INSTRUCTIONS
Selecting the saw blade
The jigsaw is supplied with 3 saw blades, each with different teeth. the profile and the
teeth vary according to the material that you want to saw. A fine tooth will give you a
smooth and precise saw cut.
Use a narrow profile if you want to saw curves or if you are going to saw figures.
The maximum saw capacity in wood is 70 mm with the enclosed saw blades. With special
saw blades, this machine can saw work pieces till 110 mm. To select the right saw,
proceed as follows:
• First of all try a saw blade with coarse teeth.
• If you don't get a smooth and precise saw cut, try a saw blade with a finer tooth.
• For plastic, aluminium and steel always use a saw blade with a very fine tooth.
In general you will work faster but less precisely with a coarse tooth than with a fine tooth.
For an optimum result always make sure the saw blade is sharp.
The jigsaw is suitable for all commercially available saw blades).
Saw blade
Coarse
Medium
Fine
Very fine
Assembling saw blade
Fig. 2a + 2b
Before assembling the saw blade check that the mains plug has been
removed from the socket.
Replacing/inserting the saw blade:
• Pull the lever (7) upwards
• Insert the saw blade (teeth in cutting direction) into the stroke rod until it latches.
While inserting the saw blade, pay attention that the back of the saw blade is
positioned in the groove of the guide roller.
• Release the lever; the saw blade (10) is locked.
Ejecting the saw blade:
• To eject the saw blade pull the lever upwards and at the same time remove the saw
blade out of the machine.
Adjusting the bottom plate
Fig. 3a + 3b
Adjust the angle of the bottom plate (6) as follows:
A. Loosen the socket head screws (12) with the Allen key supplied.
B. Pull the bottom plate back slightly to unlock it.
08
Type of workpiece
Wood
Wood
Plastic, aluminium, steel
Cutting curves (wood)
Ferm
• Redskabet Strømtilførslen • Kontroller om der er
er blevet afbrudt. defekter i forbindelsen til
strømforsyningen.
• Lever redskabet ind til
Deres forhandler til
eftersyn eller reparation.
• Savklingen er skæv eller • Udskift savklingen.
døv.
• Savklingen er over • Udskift savklingen.
ophedet eller skæv.
• Kullene er slidte. • Lever redskabet ind hos.
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til
at fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol,
ammoniak, osv. Den slags stoffer beskadiger kunststofdelene.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres maskinen i en solid emballage. Emballagen er
så vidt muligt lavet af genbrugsmateriale. Genbrug derfor emballagen.
Defekte og/eller kasserede elektriske eller elektroniske maskiner skal afleveres
på en genbrugsplads.
Garanti
Se venligst garantibetingelserne på garantikortet, som er vedlagt separat.
Ferm
• Afbryderen er beskadiget.
• Kontakt venligst
serviceadressen på
garantibeviset.
• Arbejdsemnet begynder at
vibrere kraftigt under
savningen.
• Redskaber kører
larmende og/eller meget
ujævnt.
• Kontakt venligst
serviceadressen på
garantibeviset.
DK
113