Manufacturer's Warranty; Spare Parts Lists - REMS Mini-Press 14 V ACC Betriebsanleitung

eng
● Wrong pressing tongs, Mini pressing tongs, wrong pressing ring (pressing
contour, size) or wrong adapter tongs, Mini adapter tongs, wrong cropping
inserts inserted.
● Pressing tongs, Mini pressing tongs, pressing ring or adapter tongs, adapter
tongs Mini stiff or defective.
● The pressure indicator LED (22) lights red (REMS Akku-Press 22 V ACC),
see 3.6.
● The strength class of the threaded bar is > 4.8 (400 N/mm
(REMS Mini M cropping tongs, REMS M cropping tongs M).
● Cropping inserts/cable cutters are blunt (REMS Mini M cropping tongs,
REMS M cropping tongs/REMS cable shears).
● Wrong Klauke pressing inserts inserted in REMS Mini Basic E01 pressing
tongs, REMS Basic E01 pressing tongs.
5.3. Fault: REMS Power-Press SE switches of repeatedly at the end of the pressing.
Cause:
● Defective drive unit.
5.4. Fault: A prominent burr is produced on the press fi tting when closing the pressing tongs, Mini pressing tongs, pressing ring or pressing segments.
Cause:
● Damaged or worn pressing tongs, Mini pressing tongs, pressing ring,
pressing segments or pressing contour.
● Wrong pressing tongs, Mini pressing tongs, pressing ring (pressing contour,
size) or adapter tongs, adapter tongs Mini inserted.
● Unsuitable matching of press fi tting, pipe and support sleeve.
5.5. Fault: Pressing jaws close without load on the pressing tongs, Mini pressing tongs offset at "A" and "B" (Fig. 1).
Cause:
● Pressing tongs, Mini pressing tongs fell to the fl oor, compression spring
bent.
5.6. Fault: Formation of burr when cropping threaded bars (REMS Mini M cropping tongs, REMS M cropping tongs).
Cause:
● Cropping inserts are blunt or broken out.
● The strength class of the threaded bar is > 4.8 (400 N/mm
6. Disposal
The drive units, batteries, rapid chargers and power supply units may not be
thrown in the household waste at the end of their useful lives. They must be
disposed of properly by law. Lithium batteries and battery packs of all battery
systems may only be disposed of in the discharged state, all contacts of incom-
pletely discharged lithium batteries and battery packs must be covered with
insulating tape.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference and in a fully assembled condition. Replaced products and
parts shall become the property of REMS.
● Check the labelling on the pressing tongs, the Mini pressing tongs, the
pressing ring, the adapter tongs, Mini adapter tongs and cropping inserts and
change if necessary.
● Do not use the pressing tongs, Mini pressing tongs, pressing ring or adapter
tongs, adapter tongs Mini any further! Clean and lightly grease the pressing
tongs, Mini pressing tongs, adapter tongs, adapter tongs Mini with machine oil
or replace them with new ones.
● Have the drive unit checked/repaired by an authorised REMS customer service
workshop. Re-press the press fi tting or replace it by a new one. Observe the
installation instructions of the press fi tting system.
) ● Note strength class of the threaded bars.
2
● Turn or change cropping inserts/change cable cutters.
● Observe and follow the system provider's instructions, change the pressing
inserts if necessary.
Remedy:
● Have the drive unit checked/repaired by an authorised REMS customer service
workshop.
Remedy:
● Replace the pressing tongs, Mini pressing tongs, pressing ring with new ones.
● Check the labelling on the pressing tongs, Mini pressing tongs, pressing ring or
adapter tongs, adapter tongs Mini and change if necessary
● Check the compatibility of the press fi tting, pipe and support sleeve. Observe
the installation and assembly instructions of the manufacturer/supplier of the
press fi tting system to be pressed and contact him if necessary.
Remedy:
● Send the pressing tongs, Mini pressing tongs to an authorised REMS customer
service workshop for inspection.
Remedy:
● Turn or change cropping inserts.
). ● Note strength class of the threaded bars.
2
The user shall be responsible for the cost of shipping and returning the product.
A list of the REMS-authorized customer service stations is available on the
Internet under www.rems.de. For countries which are not listed, the product
must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer's warranty is REMS
GmbH & Co KG, Stuttgarter Str. 83, 71332 Waiblingen, Deutschland.
8. Extension of the manufacturer's guarantee to 5 years
For the drive units listed in these operating instructions it is possible to extend
the guarantee time of the above manufacturer guarantee to 5 years by registering
the drive unit under www.rems.de/service within 30 days of handover to the
fi rst user. Claims from the extension of the manufacturer guarantee can only
be made by the registered fi rst users on condition that the rating plate on the
drive unit is not removed or changed and the data are legible. Cession of the
claims is excluded.

9. Spare parts lists

For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng
21