Technical Data; Before Starting The Equipment; Attachment - Scheppach 5901501905 Original Bedienungsanleitung

6. Technical data

Electro motor
Power
Revolutions n0
Saw band length
Saw band width
Saw band width max.
Cutting speed
Passage height
Passage width
Table size
Table size with min.
extension
Table size with max.
extension
Slewing range of the table
Max. size of the workpiece
Overall weight
Subject to technical modifications!
* Operating mode S1, continuous operation
** Operating mode S2, short-term operation with con-
stant load; Duration of nominal operation
The work piece must have a minimum height of 3 mm
and a minimum width of 10 mm.
The total noise values determined in accordance with
EN 61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection!
The effects of noise can cause a loss of hearing. Total
vibration emission values (vector sum of three direc-
tions) determined per EN 61029.
32 | GB
230 - 240 V ~ 50 Hz
S1* 250W,
S2** 30 min 350W
1400 min
-1
1400 mm
3.5 - 12 mm
12 mm
900 m/min
0 - 80 mm
200 mm
300 x 300 mm
380 x 300 mm
535 x 300 mm
0° - 45°
400 x 400 x 80 mm
19 kg
77.4 dB(A)
3 dB
90.4 dB(A)
3 dB
www.scheppach.com
7.

Before starting the equipment

Make sure the machine stands securely, i.e. bolt it to a
workbench or solid base. There are two holes for this
purpose in the machine foot.
• The saw table must be mounted correctly.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
• Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the ma-
chine's moving parts run smoothly.
• Before you connect the machine to the power sup-
ply, make sure the data on the rating plate is the
same as that for your mains.

8. Attachment

m ATTENTION! Before all maintenance, set-up and
assembly work on the band saw, unplug the mains
plug.
Assembly tools
1 Open-ended spanner, size 10/13
1 Allen key, size 3
1 Allen key, size 4
1 Screwdriver
The saw table and table extension are not assembled
for packaging reasons.
8.1 Assembling the saw table (Fig. 2-3)
• Remove the wing nut (21), the locking handle (22),
the two washers and the clamping plate (23). (Fig. 2)
• Guide the saw table (7) over the Bandsaw blade
(26). Fasten it to the two screws on the machine
frame with the plate (23), the two washers, the wing
nut (21) and the locking handle (22). (Fig. 3)
• Fit the bolt M6x35 (36) with two washers (37) and
the nut (38) to the table. (Fig. 3)
8.2 Fitting the table width enlargement
(Fig. 4 + 4.1 + 4.2 + 4.3 + 4.4)
• Remove the two bolts (39) and washers (40) from
the table width enlargement (8). (Fig. 4)
• Slide the table width enlargement (8) onto the table
(7) mounted on the machine. Ensure that the clamp-
ing lever (10) is open (Fig. 4.1+4.2).