Programming The 763Xx Series Signals; Other Settings; General Settings - Märklin Central Station Bedienungsanleitung

4.5. Programming the 763xx Series Signals

The following steps must be carried out to program the 763xx series
digital signals (Examples: 76391, 76393, etc.):
1. Leave the signal's electronic circuit in its packaging. The signal's
electronic circuit must be clipped into the contact bracket in the
packaging in order to be programmed.
2. Set up the appropriate controls for the signal in question in the
solenoid accessory list on the Central Station. Make sure that you
have the correct address set for the signal controls. Select the
"Momentary" mode of operation for the button function. Important:
Set the switching duration at 2,500 milliseconds for the program-
ming procedure. On signals with a distant signal mounted on
them, don't forget to set up the controls on the Central Station for
the home signal part of these signals.
3. Place the new control element on one of the 18 operation levels so
that you can control this solenoid accessory.
3. Turn the Central Station off.
4. Remove the connection for the Central Station to the layout. Only
connect the new signal to be programmed to the layout output on
the Central Station.
5. Turn the Central Station on. As soon as the Central Station is ready
to be operated, press the STOP button (emergency stop).
6. Press the GO button on the Central Station. The signal aspect on
the signal will begin to change back and forth between two states.
The following procedure depends on the signal being programmed.
76391/76393/76371/76372: Activate the signal briefly on the
screen. The signal will be programmed within the switching durati-
on that has been set for its controls (2,500 milliseconds).
76392/76394: Switch the signal to aspect Hp1. Wait until the sig-
nal begins to show alternating different signal aspects. Now switch
the signal to aspect Hp2.
76395/76397: The first step is the same as for the 76391 or 76393
signals. After that the distant signal will begin to change back and
forth between two signal aspects. Now activate the signal aspect
Hp1 or Hp0 for the home signal mounted on this signal. If the
distant signal is assigned to a two-aspect home signal, then press
the signal aspect function Hp1 or Hp0 a second time if the distant
signal has started showing alternating different signal aspects
again. In the other situation activate the signal aspect Hp2 on the
home signal mounted on this signal.
7. The signal is now programmed. Turn the Central Station off. Remo-
ve the signal from its packaging and install it on the layout.
Important:
• Do not begin the other steps until the signal is first
changing back and forth between the two signal aspects.
• It only takes a very short amount of time to activate the
switching commands. The necessary switching duration
is given with the entry of 2,500 milliseconds. When you
are through with the programming procedure, you should
change this switching duration to a value more commonly
used for regular operation of the signals (Example: 500
milliseconds).
• If you pause too long between the individual steps,
the signal will turn off the programming procedure on
its own. In this situation, start the entire process again
from the beginning by pressing the "STOP" button on the
Central Station.

5. Other Settings

The Central Station also allows you to change several basic opera-
tions parameters. The submenu "Setup" is used to do this.
Recommendation: Do not carry out the following steps, until you
have pressed the "STOP" button (emergency stop).
Press the setup symbol in the menu list on the upper
edge of the screen. A selection field will appear, which
will give you access to various selection fields.

General Settings

In this area you can set the language used on the Central Stati-
on, change the brightness of the background lighting, change the
contrast for the screen, and carry out a "RESET" of the entire Central
Station.
Important: When you do a reset of the entire Central
Station, all of the data that has been entered
is deleted! A reset of the entire Central
Station is done without asking you a
second time if you want to have the
reset done.
Do not confuse a reset of the entire Central Station with
the reset of the data in a locomotive!
If you want to change the language on the screen, touch
the arrow to call up the outer field. All of the available
language versions will appear, and they can be selected
by touching the word for the desired language.
The values set for the background lighting and for the con-
trast are represented by two horizontal bars. The values
can be changed either with the control knob or with the control areas
to the right and left of the bars. The bars must first be activated by
touching them so that the control knob changes the values to the
desired ones.
Note: Please have the hardware and software version numbers given
in this settings field handy before you call the Märklin telephone ser-
vice for help. This will result in a more efficient malfunction analysis.
Locomotive Operations Screen Settings
Possible Settings:
1. Assuming control of locomotives: Setting for whether a
locomotive called up on one locomotive controller can
be controlled at the same time on another controller.
(parallel operation)
2. Numbering functions: On models with several
functions it may happen that several auxiliary
functions (example: sound effects functions)
are displayed with the same symbol. Activating this
function will result in consecutive numbering of these
symbols.
3. Start Mode: Setting for whether the former operating
data for locomotives (speed, direction of travel) is sent
out to the models again after the Central Station is
turned on.
These functions are activated or deactivated by touching the square
control area before the text for each function.
Aktiviert bzw. deaktiviert werden diese Funktionen durch Berühren
der quadratischen Schaltfläche vor dem jeweiligen Text.
Components in the System
With this submenu you can change various defaults for
other components (Mobile Station) connected to the
Central Station. All of the recognized components are
first presented in a selection window. Using the methods
already described before in this manual, select
the desired component in this window.
In our example in the upper right we are dealing
with a Mobile Station connected to the Central
Station. Using the following submenu, you can
assign locomotives from the Central Station's locomotive
list to this Mobile Station, locomotives which are to be
controlled with the Mobile Station. You therefore have the
possibility of allowing another operator to have access to
a limited number of locomotives. The locomotive list in the
Mobile Station has a capacity for up to 10 entries.
After you have selected the desired component, a settings field will
appear in which loco-
motives for the Mobile
Station's locomotive list
are can be selected or re-
moved from this list. This
is done in the same man-
ner as with the generation
of a multiple unit motive
power combination from
the Central Station's loco-
motive list. The changes
are not active until the
27
Expanded
Edit Loco List
Locos to select
Mobile Station
Steam Loco
Steam Loco
Central Station 60212
Übernehmen von L
Übernehmen ein
Funktionen numme
Funktionen mit g
Startmodus
Bisherige Gesch