Emergency Stop/ „Stop" Button; Release / "Go" Button; Operation Locomotives/ Trains; Setting Up Mfx Locomotives - Märklin Central Station Bedienungsanleitung

3.2.4. Emergency Stop / „STOP" Button
Pressing the "STOP" Button:
The electrical power for the layout and for the programming track is
turned off. Boosters or other power units connected to the system
also shut off. The red light in the "STOP" button comes on. When
there is an overload, the Central Station auto-
matically switches to this mode.
Ending this condition:
1. Find and correct any short circuit or cause for
the overload.
2. Press the "GO" button. (=> 3.2.5)
Note: When you have pushed the emergency
stop button, changes for the commands to the locomotives and so-
lenoid accessories can still be entered on the Central Station. These
new commands are not carried out until the layout is again supplied
with power.
When the STOP status is activated by a short
circuit, a short circuit symbol will appear for se-
veral seconds in the lower left and right corners
of the screen. After that the not "EMERGENCY
STOP" will appear there, just as if you had
pressed the "STOP" button.

3.2.5. Release / "GO" button

The "GO" button is pressed to resume opera-
tions again on a layout, when the power to it
has been shut off (emergency stop). ). When the
green light goes on in the "GO" button, the red
light in the "STOP" button is turned off. Voltage
is now available again at the layout outputs on
the Central Station.
Note: If the Central Station immediately goes back into the emer-
gency stop mode (the red light in the "STOP" button lights up) on its
own, then usually there is a short circuit on the layout. This must be
corrected before operations can be resumed on the layout.
3.3. Operating Locomotives / Trains

3.3.1. Setting up Mfx Locomotives

Generally, mfx locomotives register themselves on the Central Sta-
tion. All you have to do is place the locomotive on the track. Make
sure when doing this that the layout has power flowing to it (release
mode). The locomotive may not be initially place in an area of the
track that is not continuously supplied with electrical power (examp-
les: signal block, storage siding where you can turn the power off,
etc.) or an area of the layout that is connected through the Connect
6017 unit (item no. 60129) to a 6015 or 6017 Booster.
The transfer of data from the mfx locomotive to the Central Station
and reverse takes about 1 minute. If the mfx locomotive is placed on
the layout for the first time, while the latter is in the middle of ongoing
operations, then the registration process may take up 3 minutes.
mfx
Two mfx symbols will appear in the upper menu list on the screen
while an mfx locomotive is being registered. These symbols report
the progress of the registration process. When these symbols are
completely filled in with black, you must press on one of the two
symbols. The newly registered locomotive is taken into the locomo-
tive controller to which you have assigned it, and it is also taken into
the locomotive list at the same time.
Mfx locomotives can only be registered one after the other the first
time out. The registration process for another locomotive cannot take
place until the first locomotive is completely registered.
Tip: Place locomotives to be registered one after the other on the
layout. If several locomotives to be registered are on the
track at the same time, the complete process can take
considerably longer to complete.
Central Station 60212

3.3.2. Setting up Locomotives with Delta or Digital Decoders

The Central Station is also able to control the different Märklin Delta
or Digital decoder generations, which are designed for operation with
Märklin Delta or Märklin Digital (both the 6020 Central Unit and the
6021 Control Unit and their variants).
The following steps can be done on the right or the left side of the
train controls on the Central Station. The operation steps on the left
side of the train controls are demonstrated by way of example.
Press the menu button in the upper left corner of the display screen.
A selection menu will appear on the
display screen next to this button. The
arrow in the line "New Locomotive"
indicates that additional selection menus
can be opened by selecting these lines.
There are two different ways to select
the different submenus:
a: Direct selection by touching the
screen at the line of text in question.
!
b: By turning the left control knob on the
Central Station. The black cursor bar will
then wander from line to line. The submenu on which the black cur-
sor bar is now standing is activated by pressing on the control knob.
Select the line "New Locomotive" and activate the submenu. Two
new selection fields will appear, "enter manually" and "from databa-
se".
Enter manually - The entry in the locomotive list (name, address, etc.)
GO
is generated completely by you the operator.
From database - The locomotive data
is generated by going into a database
integrated into the Central Station. This
database has factory data for many of
the earlier Märklin models.
Variation 1: From database
Select the line "from database" either
with the control knob or by directly tou-
ching the screen. A menu with different
entries from the integrated database will appear.
�
mfx
� �
1 = Locomotive selected
2 = Data lines sorted by item number
3 = Data lines sorted by name
4 = End without selecting a locomotive
5 = Select current data line
6 = Go down one data line
7 = Position indicator for the entire list
8 = Go up one data line
Selecting a data line:
Select the desired locomotive by moving the selection bar cursor (1)
up and down by turning the control knob and then pressing down on
the control knob.
Or, the data line list can be navigated by pressing on the arrow but-
tons (6 or 8). The data line you want will be selected by touching the
check mark field (5). The process can be ended without selecting a
locomotive by touching the "x" field (4).
20
New locomotive
New M.U. power
Process locomotive
Delete locomotive
Select Locomotive from Database
003 131-0 (3795)
003 131-0 (3395)
01 067 (55900)
01 1053 (39104)
123 ABC
New locomotive
New M.U. power
Process locomotive
Delete locomotive
Enter manually
From database
�
�
�
� �