Technical Data - Parkside PKO 24 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

22. In case of pressures above 7 bar, it is recommended to
equip supply hoses with a safety cable (e. g. a wire rope).
23. Avoid over-stressing the piping system by using flexible
hose connections to prevent kinking.
24. Ensure that oil cooling devices are kept clean and protective
devices remain in operational condition.
25. Risk of burns from hot oil
- Wear suitable protective gloves.
- Never work with the compressor near naked flames.
- Be careful not to spill oil.
26. Motor start-up is prohibited at low temperatures below
0 °C.
Additional safety instructions
Safety instructions for working with compressed
air and blasting guns
• The compressor pump and lines can become very hot during
operation. Touching these parts will burn you.
• The air which is sucked in by the compressor must be kept
free of impurities that could cause fires or explosions in the
compressor pump.
• When releasing the hose coupling, hold the hose coupling
piece with your hand. This way, you can protect yourself
against injury from the rebounding hose.
• Wear safety goggles when working with the blow-out pistol.
Foreign bodies or blown off parts can easily cause injuries.
• Do not blow at people with the blow-out pistol and do not
clean clothes while being worn. Danger of injury!
Safety information for paint spraying
• Do not process any paints or solvents with a flash point
below 55° C. Risk of explosion!
• Do not heat up paints or solvents. Risk of explosion!
• If hazardous liquids are processed, wear protective filter
units (face guards). Also, adhere to the safety information
provided by the manufacturers of such liquids.
• The details and designations of the Ordinance on Hazardous
Substances, which are displayed on the outer packaging
of the processed material, must be observed. Additional
protective measures are to be undertaken if necessary,
particularly the wearing of suitable clothing and masks.
• Do not smoke during the spraying process and/or in the
work area. Risk of explosion! Paint vapours are easily
combustible.
• Never set up or operate the equipment in the vicinity of a fire
place, open lights or sparking machines.
• Do not store or eat food and drink in the work area. Paint
vapours are harmful to your health.
• The work area must exceed 30 m³ and sufficient ventilation
must be ensured during spraying and drying.
• Do not spray against the wind. Always adhere to the
regulations of the local police authority when spraying
combustible or hazardous materials.
• Do not process media such as white spirit, butyl alcohol and
methylene chloride with the PVC pressure hose. These media
will destroy the pressure hose.
• When used in conjunction with spray accessories (e. g. a
paint spray gun): Keep distance to the device while filling the
spray equipment and do not spray towards the compressor.
Operation of pressure vessels
• Anyone who operates a pressure vessel must keep this in
good working order, operate and monitor it correctly,
perform the necessary maintenance and servicing works
immediately and implement safety measures as required
according to the circumstances.
• The regulatory authority can instruct necessary monitoring
measures in individual cases.
• A pressure vessel must not be operated if it exhibits a defect
that poses a danger to personnel or third parties.
• Check the pressure vessel for rust and damage each time
before use. The compressor shall not be operated if the
pressure vessel is damaged or rusty. If you discover damage,
please contact the customer service workshop.
Keep these safety instructions in a safe place.
Residual risks
Comply with the stipulated maintenance and safety instructions
in the operating instructions.
Remain attentive at all times when working, and keep third
parties at a safe distance from your work area.
Even when the device is being used properly, there will always
be certain residual hazards that cannot be completely ruled
out. The following potential hazards can arise due to the type
and design of the device:
• Unintentional starting up of the product.
• Damage to hearing if the stipulated hearing protection is not
worn.
• Dirt particles, dust etc. can get irritate the eyes or face
despite wearing safety goggles.
• Inhaling swirled up particles.
Warning!
This power tool generates an electromagnetic field during
operation. This field can impair active or passive medical
implants under certain conditions. In order to prevent the risk
of serious or deadly injuries, we recommend that persons
with medical implants consult with their physician and the
manufacturer of the medical implant prior to operating the
power tool.

7. Technical data

Mains connection ................................................ 230 V∼ 50 Hz
Motor power ................................................................. 1800 W
Operating mode .......................................................................S1
Compressor speed .....................................................2850 min
Pressure vessel capacity ......................................... approx. 24 l
Maximum operating pressure............................ approx. 10 bar
Theoretical intake capacity ...........................approx. 260 l/min
Sound pressure level L ............................................ 72.9 dB(A)
PA
Sound power level L .............................................. 92.9 dB(A)
WA
Uncertainty K .......................................................... 2.59 dB
PA/WA
Protection category .............................................................. IP32
Device weight ....................................................approx. 26.8 kg
Oil (SAE 15W 40) ...............................................approx. 0.25 l
Maximum altitude (above mean sea level) ...................1000 m
-1
GB 5