Service Information; Transport; Disposal And Recycling - Parkside PKO 24 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

11.5 Changing the oil (fig. 1, 9, 10)
Switch the motor off and unplug the mains plug from the power
outlet. Remove the oil sealing plug (16). After releasing any
air pressure you can unscrew the oil drain screw (12) from the
compressor pump (13).
To prevent the oil from running out in an uncontrolled manner,
hold a small metal chute under the opening and collect the
oil in a vessel. If the oil does not drain out completely, we
recommend tilting the compressor slightly. When the oil has
drained out, re-fit the oil drain screw (12).
Dispose of the old oil at a drop-off point for old oil.
To fill in the correct quantity of oil, make sure that the compressor
stands on an even surface. Fill new oil through the oil filling
opening (20) until it comes up to the maximum level. This is
marked with a red dot on the oil-level window (18) (fig. 10).
Do not exceed the maximum filling quantity. Overfilling the
equipment may result in damage. Reinsert the oil sealing plug
(16) into the oil filling opening (20).
11.6 Cleaning the air filter (fig. 3, 11, 12)
The air filter (15) prevents dust and dirt being sucked in. It is
essential to clean this air filter (15) after at least every 300
hours in service. A blocked air filter significantly reduces the
compressor power.
Remove the air filter (15) by opening the wing screw (15b).
Then pull off the filter cover (15e). Now you can remove the
filter element (15c) and the filter housing (15d). Carefully tap
out the filter element (15c), the filter cover (15e) and the filter
housing (15d). These components must then be blown out with
compressed air (approx. 3 bar) and reassembled in reverse
order.

11.7 Service information

With this product, it is necessary to note that the following
parts are subject to natural or usage-related wear, or that the
following parts are required as consumables.
Wearing parts*:Air filter
* may not be included in the scope of supply!
11.8 Storage
m Attention!
Pull out the mains plug and ventilate the equipment
and all connected pneumatic tools. Store the
compressor in such a way that it cannot be used by
unauthorised persons.
m Attention!
Store the compressor only in a dry location which
is not accessible to unauthorised persons. Always
store upright, never tilted! Oil may leak out!
11.8.1 Releasing excess pressure
Release the excess pressure by switching off the compressor
and using the compressed air which is still left in the pressure
vessel (8), e. g. with a compressed air tool running in idle mode
or with a blow-out pistol.
8 GB

12. Transport

Use the transport handle (1) to transport the device, and drive
the compressor with it.
When lifting the compressor, note its weight (see Technical
data).
Ensure that the load is well secured when transporting the
compressor in a motor vehicle.

13. Disposal and recycling

The device is supplied in packaging to avoid transport
damages. This packaging is raw material and can thus be used
again or can be reintegrated into the raw material cycle.
The device and its accessories are made of different materials,
such as metals and plastics. Take defective components to
special waste disposal sites. Check with your specialist dealer
or municipal administration!
The packaging is wholly
environmentally-friendly materials that can be
disposed of at a local recycling centre.
Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
electrical devices.
Old devices must not be disposed of with household
waste!
This symbol indicates that this product must not be
disposed of together with domestic waste in compliance
with the Directive (2012/19/EU) pertaining to waste
electrical and electronic equipment (WEEE). This
product must be handed over at the intended collection point.
This can be done, for example, by returning it when purchasing
a similar product or delivering it to an authorised collection
point for the recycling of old electrical and electronic devices.
Improper handling of waste equipment may have negative
consequences for the environment and human health due to
potentially hazardous substances that are often contained in
electrical and electronic equipment. By properly disposing of
this product, you are also contributing to the effective use of
natural resources. You can obtain information on collection
points for waste equipment from your municipal administration,
public waste disposal authority, an authorised body for the
disposal of waste electrical and electronic equipment or your
waste disposal company.
composed of