Inhaltsverzeichnis; Introduction; Description; Technical Data - CEA COMPACT 240M Bedienungsanleitung & Ersatzteilliste
Vorschau ausblenden
Andere Handbücher für COMPACT 240M:
- Bedienungsanleitung & ersatzteilliste (92 Seiten)
Inhaltsverzeichnis
Werbung
EN
ENGLISH
Key to the electrical diagram
Colour key
Adjustment of electronic PCB
Meaning of graphic symbols on machine
Meaning of graphic symbols on rating plate
Spare parts list
Entrainment mechanism
Drive mechanism
Ordering spare parts
Introduction
Thank you for purchasing one of our products. Please read in-
structions on use in this manual as well as the safety rules
given in the attached booklet and follow them carefully to get
the best performance from the plant and be sure that the parts
have the longest service life possible. In the interest of custom-
ers, you are recommended to have maintenance and, where
necessary, repairs carried out by the workshops of our service
organisation, since they have suitable equipment and specially
trained personnel available. All our machinery and systems are
subject to continual development. We must therefore reserve
the right to modify their construction and properties.
Description
8
8
Semiautomatic single-phase continuous wire welder with switch
adjustments and incorporated feeder, suitable for use with a
8
gas mixture or CO
2
suitable for use in medium carpentry and body shops, in agri-
8
culture and for maintenance.
8
The main features of COMPACT 240M welders are:
• Exceptional welding characteristics with all materials as a re-
9
sult of inductance levelling.
• Excellent welding performance on thin metal sheets.
10
• Provided with standard gas cylinder trolley with sturdy wheels
10
to facilitate movement.
• Free-standing metal structure with front panel in special
10
shockproof fibre.
• Tough handle for ease of movement.
10
• Adequate internal space for conveniently storing metal spools
11
(Max 300 mm - Max 20 kg).
• Euro torch connection.
11
• 42 V D.C. geared motor with electronic control of wire speed.
• 2 roll wire drawing unit.
11
• A gas solenoid valve.
11
• Switch for selecting 2-step and 4-step modes.
• Potentiometer for the wire speed adjustment.
12
• Potentiometer for "Burn back" with external adjustment.
• Potentiometer for motor start-up adjustment.
12
• Potentiometer with switch for adjusting spot-welding times.
13
Technical data
13
80
The technical data for this equipment is summarized in the ta-
ble 1.
81
84
Usage limits (IEC 60974-1)
85
The use of a welder is typically discontinuous, in that it is made
up of effective work periods (welding) and rest periods (for the
86
positioning of parts, the replacement of wire and underflushing
88
operations etc). This welding machine is dimensioned to supply
I
max nominal current (250A), in complete safety, for a work
2
90-93
period amounting to (20%) of total usage time. The regulations
in force establish the total usage time to be 10 minutes. If the
94
permitted work cycle time is exceeded, an overheat cut-off oc-
95
curs to protect the components around the welder from dan-
gerous overheating. The yellow thermostat LED located on the
96
machine rack panel lights up when the overheating protection
trips. After several minutes the overheat cut-off rearms auto-
matically (yellow LED off) and the welder is ready for use again.
How to lift up the system
Before lifting the unit, open the bag containing the eyebolts (at-
tached to machine), remove the two eyebolts complete with fi-
bre washers and mount them on the upper part of the cover.
IMPORTANT: Only lift the unit using the two eyebolts.
The wire-feeder has a handle and a hook so that it can be
hung up.
NOTE: The lifting and transporting devices conform with Eu-
ropean regulations. Do not use other equipment to lift or trans-
port the feeder.
8
and with cored wires with and without gas;
Werbung
Inhaltsverzeichnis
