Scrapping Of The Machine; Packing Lifting And Transport; Checks Upon Delivery - Comet CPS 55 ADVANCE BYT Bedienungsanleitung

tions must be carried out in environments with ade-
quate lighting and only after having disconnected the
machine from the electric power supply by detaching
the battery connector.
☞ All work on the electrical system and all mainte-
nance and repair operations (especially those not
explicitly described in this manual) should be carried
out only by authorized service centers or by special-
ized technical personnel who are experts in the sector
and in the pertinent safety regulations.
☞ The machine owner can only use original acces-
sories and spare parts supplied exclusively by the
manufacturer since such parts are the only ones
that guarantee that the equipment will operate
safely without any problems. Do not use parts disas-
sembled from other machines or other kits as spare
parts.
☞ Before each use, check the machine and, in particu-
lar, check that the battery charging cable and the con-
nector are in good condition and safe for use. If they
are not in perfect condition, do not use the machine
for any reason until an authorized specialist repairs
the defective parts.
☞ If foam or liquid is noted, immediately turn off the
suction motor.
☞ Do not use the machine on textile flooring, such as
rugs, carpeting, etc.
Wax, foaming detergents or dispersions along the
hoses may cause serious problems for the machine
or clog the hoses.
2.2.

SCRAPPING OF THE MACHINE

If the machine will no longer be used, remove the
batteries and dispose of them in accordance with the
eco-compatibility regulations as set forth in European
standard 91/157/EEC or deposit them in an author-
ized collection centre.
To dispose of the machine, comply with the current
laws where it is used:
- disconnect the machine from the mains and clean
it after emptying any liquids;
- separate the machine into groups of homoge-
neous materials (plastics in accordance with the
recycling symbol, metals, rubber, packing). For
parts containing different materials, contact the
competent authorities;
Each homogeneous group must be disposed of in ac-
cordance with recycling laws.
In addition, it is recommended to eliminate those
parts of the machine that may be dangerous, espe-
cially for children.
As owner of an electrical or electronic product,
you are not allowed by law (according to
EU-Directive 2002/96/EC of 27 January 2003
on waste electrical and electronic equipment
and the particular national laws of the EU-Member
States transforming this Directive) to dispose of this
product or its electrical/electronic accessories as un-
sorted domestic waste. You shall use the designated
gratis possibilities for return instead.
3. HANDLING INFORMATIONS
3.1.

PACKING LIFTING AND TRANSPORT

• During all lifting or transport operations, make
sure that the packed machine is securely anchored
to prevent it from tipping over or falling accidentally.
Transport vehicle loading and unloading operations
must be carried out with adequate lighting.
The packed machine must be handled using ade-
quate devices, making sure not to damage/strike any
part of the packing, not to tip it over and to be very
careful when placing it on the ground.
☞ All these instructions also apply to the batteries
and the battery charger.
3.2.

CHECKS UPON DELIVERY

☞ When the goods are delivered (machine, battery
or battery charger) by the transporter, carefully check
the condition of the packing and its contents. If the
contents have been damaged, notify the transporter
and reserve the right, in writing (select the word "re-
serve" on the document), to submit a claim for com-
pensation before accepting the goods.
3.3. UNPACKING
• Wear safety clothing and use adequate tools to
limit the risks of accidents.
The machine is packed with in a cardboard housing
placed on a wooden crate; to unpack the machine
carry out the following steps:
- Use scissors or clippers to cut and eliminate the
plastic straps.
- Slip off the cardboard housing from the top of the
packed machine.
- Remove the envelops inside and check their
contents (use and maintenance manual, battery
charger connector)
- Remove the metallic brackets or plastic straps that
secure the machine to the pallet.
- Release the brushes and the squeegee from the
packing.
- Take the machine off the pallet (pushing it back-
ward) by using an inclined surface that is solidly
attached to the floor and to the pallet.
Keep all the pieces of the packing since they might be
useful in the future to protect the machine and the
accessories during transport to another location or to
authorized service centers. If not, the packing can be
disposed in accordance with current disposal laws.
27