Product Identification; Technical Modifications - Comet CPS 55 ADVANCE BYT Bedienungsanleitung

1. GENERAL INFORMATION
1.1. MANUAL PURPOSE
To make it easier to read about and look up various
subjects, refer to the table of contents at the begin-
ning of the section in your language.
This manual has been prepared by the manufacturer
and is an integral part of the product. As such, it must
be kept in a safe place for the machine's entire service
life until demolition.
The customer must ensure that machine operators
have read or are familiar with the contents of this
manual so that they strictly follow the instructions
described herein.
Constant compliance with the instructions provided
in this manual is the only way to guarantee the best
results in terms of safety, performance, efficiency and
service life of the product you now own. Non- com-
pliance with these rules may cause injuries to people
and damage to the machine, the scrubbed surface
and the environment: in no case can such injuries or
damage be attributed to the manufacturer.
This manual refers in detail to the machine and pro-
vides instructions and descriptions only about the
battery and the battery charger provided.
1.2. TERMINOLOGY AND SYMBOL LEGEND
For the sake of clarity and to efficiently highlight
the various aspects of the instructions provided,
terms and symbols were used that are defined and
illustrated here below:
- Machine. This definition replaces the commercial
name to which this manual refers.
- Operator. An operator is considered the person
who normally uses the machine and is familiar
with its operating features but does not have the
specific technical skills to work on that machine.
- Technician. A technician is considered a person
who has the experience, technical education,
legislative and regulatory knowledge that allows
him to carry out any type of required work, and
the ability to recognize and to avoid possible risks
during machine installation, operation, handling
and maintenance.
- INDICATION SYMBOL ( ☞ ). Particularly impor-
tant information to avoid machine malfunctions.
- ATTENTION SYMBOL ( • ). Very important infor-
mation to avoid serious damage to the machine
and to the environment in which it operates.
- DANGER SYMBOL ( • ). Vital information to avoid
serious (or extreme) consequences affecting the
health of persons and causing damage to the
product and the environment in which it operates.
1.3.

PRODUCT IDENTIFICATION

The nameplate located in the backside of the ma-
chine contains the following informations:
• Manufacturer ID
• CE mark
• Model code
• Model
• Overall power rating
• Serial number
• Year built
• Weight with maximum load
1.4. SPECIFIC USE
This machine is a floor scrubber-drier: it must be used
to scrub and to vacuum liquids of flat, rigid, horizon-
tal, smooth or moderately rough and uniform floors
that are free from obstacles in both civic and indus-
trial environments. Any other use is prohibited.
Please refer very carefully to the safety information
reported in this manual.
The scrubber-drier distributes a quantity of a water
and detergent solution (adjustable) on the surface to
be cleaned, while the brushes remove any dirt on the
ground. The machine's suction system, using a ground
squeegee, perfectly dries the liquids and the dirt just
removed from the front brushes in a single pass.
By efficiently combining a cleaning detergent with
various types of brushes (or abrasive disks), the ma-
chine can adapt to all the various combinations of
floors and dirt.
1.5.

TECHNICAL MODIFICATIONS

This machine was designed and built in accordance
with the fundamental requirements for user safety
and health as set forth in European directives. For this
reason the CE mark was placed on the ID label. The
European directives to which the equipment con-
forms are referenced in the Certificate of conformity
annexed to this manual. This certificate will no longer
be valid if the equipment is modified in any way with-
out the manufacturer's prior authorization.
The manufacturer reserves the right to make techni-
cal modifications to the product, without prior notice,
in order to make the necessary technical upgrades or
improvements. For this reason, some details of your
machine may be different from the information in the
sales catalogues or from the illustrations presented
in this booklet. However, this will not reduce safety
or invalidate the information supplied to this regard.
25