Comet CPS 55 ADVANCE BYT Bedienungsanleitung Seite 39

6.10. ADJUSTING THE AMOUNT OF THE
DETERGENT IN THE CLEANING SOLUTION
The adjustment of the amount of detergent to be
used in the cleaning solution is carried out through
the push selector on the control panel (Photo 6 - G) .
Pressing the selector multiple times will increase the
amount of detergent dispensed; the dilution of the
detergent dispensed is displayed on the control panel
(Photo 6 - G) through progressive levels highlighted in
the graphic symbol (Photo 7).
The percentage of dilution of the detergent varies
depending on the amount of clean water delivered,
adjustable through the control lever (Photo 7); when
the clean water outflow is half of the total possible
amount, the percentage of dilution is shown in (
Photo 28 ); when the clean water outflow is set on
the full amount the dilution percentage is shown in
( Photo 28 ).
A
Photo 28
A) Water flow adjusting lever
B: tap closed
C: tap opened
6.11. DRIVING THE MACHINE
Model "B" - "BT" DC 24V
- Put the ignition key ( Photo 4 - H ) in and turn ON
the machine.
- Check the battery charge status on the battery
power test placed on the control panel ( Photo 4 - E ).
- Switch ON the brush motor switch ( Photo 6 - A ).
• The brush will start the rotation only when the
operator will pull the brush operation lever ( Photo
2 - A ).
- Switch ON the suction motor switch ( Photo 6 - B )
- Open the solution water valve rotating the lever (
Photo 4 - A ).
- Lower the squeegee unit by using the lift/lower
lever ( Photo 4 - B ).
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo 2 - A ) to start the
brush rotation and the solution water outlet; re-
leasing the lever the brush rotation will stop after
few seconds.
B
C
• Remember to lift the squeegee before driving re-
verse to avoid damaging it.
6.12. WORK METHOD
6.12.1. PREPARATION AND WARNINGS
Remove any loose solid residue from the surface
to be treated (using suitable tools, such as vacuum
cleaners, sweepers, etc.). It this is not done, the
solid dirt might prevent the squeegee from oper-
ating correctly, reducing drying efficiency.
Only trained personnel can drive this machine.
6.12.2. BATTERY CHARGE LEVEL CONTROLS
The sequence of lights of the battery power test
( Photo 14 ) shows the battery discharging (green
light = battery fully charged; yellow light = battery
half charged; red light = battery discharged). When
the red light turns on, turn off the brush motor, close
the detergent solution outlet, finish drying the small
residual moisture and go to the battery charging area
to charge the battery.
• The battery may be irreparably damaged if the
residual charge level drops too low (see the battery
operating manual). Do not force the battery discharge
beyond the safety limits, turning the key off and on or
in any other manner
6.12.3. DIRECT SCRUBBING OR FOR SLIGHTLY
DIRTY SURFACES
Scrubbing and drying in a single pass.
Prepare the machine as previously described and use
it as described in paragraph 7.11.
☞ Never use the machine without the detergent solu-
tion: the floor might be damaged.
6.12.4. INDIRECT SCRUBBING OR FOR VERY
DIRTY SURFACES
Scrubbing and drying in various passes.
Prepare the machine as previously described.
First set of operations:
Wash the floor as described in paragraph 7.11 without
drying the floor Allow the detergent solution to work
on the dirty floor according to what is indicated in the
information relative to the detergent used.
Second set of operations:
Proceed as explained in the previous "Direct Wash-
ing" paragraph (7.12.3) to also proceed with drying
the floor.
☞ Never use the machine without the detergent solu-
tion: the floor might be damaged.
6.12.5. POST-SCRUBBING OPERATIONS
Close the detergent solution outlet.
After having completely dried any traces of water
on the surface, wait a few seconds and then lift the
squeegee and turn off the suction motor.
Move to a suitable location to drain the tanks; empty
39