LIVSANE FDIR-V22 Gebrauchsanweisung Seite 4

LCD display description: LCD display description:
Memory group indication Memory group indication
7. Operation Instructions 7. Operation Instructions
Preparation: Preparation:
1) Check the batteries: 1) Check the batteries:
Replace the batteries to ensure power supply, if the low voltage icon appears on the display. Replace the batteries to ensure power supply, if the low voltage icon appears on the display.
2) Check the thermometer: 2) Check the thermometer:
When you press the "Power / Scan" button, the system itself tests its software and hardware. If there When you press the "Power / Scan" button, the system itself tests its software and hardware. If there
are problems, the LCD will display the "Err" symbol. Also, please make sure that the sensor lens are problems, the LCD will display the "Err" symbol. Also, please make sure that the sensor lens
is clean and there aren't any damaged parts prior to use. is clean and there aren't any damaged parts prior to use.
3) In order to get accurate measurement results, keep the thermometer in the measurement 3) In order to get accurate measurement results, keep the thermometer in the measurement
environment for 30 minutes prior to use. environment for 30 minutes prior to use.
4) Unexpected fluctuations in the ambient room temperature may decrease the accuracy of the 4) Unexpected fluctuations in the ambient room temperature may decrease the accuracy of the
measured results. measured results.
5) When measuring forehead temperature, make sure the measured area is clean and cleared of hair 5) When measuring forehead temperature, make sure the measured area is clean and cleared of hair
in order to ensure the accuracy. in order to ensure the accuracy.
Instructions for use: Instructions for use:
(1) Forehead measurement (1) Forehead measurement
When the thermometer is turned on, place the infrared probe in front of the forehead at a distance When the thermometer is turned on, place the infrared probe in front of the forehead at a distance
between 1 cm and 6 cm, then press „Power / Scan". After ca. 1 second the measurement is finished, between 1 cm and 6 cm, then press „Power / Scan". After ca. 1 second the measurement is finished,
a beep sound is heard and the LCD display shows the measurement result as below:
a beep sound is heard and the LCD display shows the measurement result as below:
• •
If the ambient temperature exceeds the range of 10 – 40,0 °C, the thermometer shows „Err" If the ambient temperature exceeds the range of 10 – 40,0 °C, the thermometer shows „Err"
• •
If the measured human temperature value is higher than 42,9 °C, it shows „Hi"; If the measured If the measured human temperature value is higher than 42,9 °C, it shows „Hi"; If the measured
temperature is lower than 32 °C, „Lo" is shown. temperature is lower than 32 °C, „Lo" is shown.
• •
If 32,0 °C ≤ temperature ≤ 37,5 °C, a green backlight lights up; If 37,6 °C ≤ temperature ≤ 42,9 °C, If 32,0 °C ≤ temperature ≤ 37,5 °C, a green backlight lights up; If 37,6 °C ≤ temperature ≤ 42,9 °C,
a red backlight lights up. a red backlight lights up.
Notice Notice
• •
When measuring the forehead temperature, you should first remove the hat and arrange the hair When measuring the forehead temperature, you should first remove the hat and arrange the hair
on the forehead in a way to prevent an influence on the measurement. on the forehead in a way to prevent an influence on the measurement.
• •
Sweat or cosmetics on the forehead will affect the measurement accuracy. Please keep the forehead Sweat or cosmetics on the forehead will affect the measurement accuracy. Please keep the forehead
clean during measurement. clean during measurement.
• •
Be careful not to point the LED light into the subject's eyes during measurement. Be careful not to point the LED light into the subject's eyes during measurement.
(2) Measurement unit selection (2) Measurement unit selection
After turning on the thermometer, press the „C / F switch button" to select the desired unit After turning on the thermometer, press the „C / F switch button" to select the desired unit
of measurement as below: of measurement as below:
V22 BOOK.indb 4 V22 BOOK.indb 4
Environment Environment
temperature icon temperature icon
Tone indication icon Tone indication icon
Measuring reading Measuring reading
Body temperature icon Body temperature icon
Low voltage indication icon Low voltage indication icon
Temperature unit indication Temperature unit indication
icon icon
4 4
18/10/2020 22:32 18/10/2020 22:32