Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Regularly check power supply cords for dama-
ge. Make sure that during such checks, the cord
is not connected to the mains voltage. Power
supply cords must adhere to the relevant VDE
and DIN requirements and the local power
company regulation. Use only cords labelled
H07RN. An imprint of the classification on the
cords is required.
•
Extension cables must have a minimum
cross-section of 1.5 mm² up to 25 m in
length; over 25 m in length, at least 2.5
mm².
•
The mains connection is fused with 16 A.
•
The customer-side mains connection must
be fused with an earth leakage circuit
breaker with a rated differential current of
maximum 30 mA.
•
Observe the safety instructions before
start-up.
•
All protective and auxiliary equipment must
be mounted.
•
Carry out retrofitting, adjustment, measu-
rement and cleaning tasks only when the
motor is switched off. Pull the plug and wait
for the rotating tool to come to a stop.
•
The rocker circular saw is designed exclusi-
vely for cross-cut sawing of firewood with a
maximum length of 1 meter.
•
Multiple pieces of wood may be sawn at the
same time. Make sure that the wood is laid
securely in the rocker
•
Make sure the logs between the two saw
blades rest properly in order to prevent any
displacement while sawing (Fig.17). Put
only as many logs as necessary to make
sure this measure is guaranteed.
•
Place the logs so that they can be held
securely with the wooden handle.
•
Close the protective hinged cover (B) to
saw (Fig. 04)
•
Use the wood retaining lever (C) when cut-
ting with the saw. Press the rocker forward
using the hand grip (D).
•
The wood may not be secured with the
hand.
•
Carry out maintenance, repair and cleaning
work as well as resolution of function dis-
ruptions only when the drive is switched off
(pull the mains plug or remove the ignition
key).
•
Check the tension in the V-belt after the
first operating hour, as well as before every
start-up.
•
All ball bearings are provided with perma-
nent lubrication. The circular saw blade is
a wear part and is to be checked before
every start-up. Only a well-sharpened,
straight-set saw blade delivers good cutting
performance. Occasional lubrication of the
saw blade is recommended.
Additional maintenance tasks: re-tension
the V-belts in the drive shaft
Changing the transmission oil
•
Refresh the transmission oil annually.
•
Use SAE 90 transmission oil.
•
The fill volume is 0.66 litres.
•
The figure (Fig.16) shows the mitre gear oil
fill screw.("S")
•
Pour in oil until it is just under the edge of
the fill hole
•
Dispose of old oil in an environmentally
friendly way!
All manuals and user guides at all-guides.com
Three-phase alternating current motor
•
Mains voltage must be 380–420 V/50 Hz.
•
Mains connection and extension cords
must be 5-poled (3 P + N + earth).
•
Extension cords cables must have a mini-
mum cross-section of 1.5 mm².
•
-The mains connection is fused with maxi-
mum 16 A.
•
During connection to the mains or change
in location, the rotational direction must be
checked; if necessary, the polarity must be
changed.
Repairs and changes to the connections of the
electrical equipment may be carried out only by
a qualified electrician.
Start-up
•
When sawing, make sure to execute the
cutting stroke slowly and carefully
•
When emptying the rocker´s outlet, make
sure there are no splinters and wood chips
between the saw rockers and the rocker´s
outlet, always keep this area clean
•
To empty the rocker (Fig.14) after the saw
cut, open the hinged guard (P) and then tip
the rocker emission (Q) outward.
•
Check the tension in the V-belt after the
first operating hour, as well as before every
start-up.
•
If you do not use the rocker circular saw for
a longer period of time, take off all springs
to preserve them.
Attention:
•
For crooked pieces of wood, the crooked
side must be pointed toward the saw
blade slit in order to keep the wood from
tipping over and jamming during the cutting
process.
Changing the saw blade of the rocker circu-
lar saw
•
Carry out maintenance, repair and cleaning
Maintenance
Tensioning the belt (Fig. 06 + 07)
The V-belt tension is to be checked after the
first operating hour and before every start-up.
To tension the belt, remove the lock nut "F" and
tighten the hex nut "G" with a jaw spanner SW
13.
Secure the tension of the belt by tightening the
check nut "H".
Now check the belt tension by laying the machi-
ne down.
(Caution: tip danger!)
Now press with the thumb on the tensioned belt;
under strong pressure, it may give only approx.
10-15 mm.
Now set the machine upright again, and tighten
the lock nut again.
Tensioning the belt with V-belt drive (Fig. 10
+ 11)
To tension the V-belt, loosen the hex screws
("M"; Fig. 11), including the hex screws on the
opposite side (total 8 pieces).
Now tighten the hex nut ("N"; Fig. 12).
To check the belt tension, unscrew the cover
found on the side of the drive cover. Now press
with the thumb on the tensioned belt; under
17
For correspondence, please supply the following
data:
•
Motor manufacturer; Motor type
•
Current type of the motor
•
Data of the machine rating plate
•
Data of the electrical control system
When returning the motor, always send the
complete drive unit with the electrical con-
trol system.
General notes for handling the
electrical equipment:
•
When switching on the motor, first move
the switch to the star, wait briefly, and then
switch to the triangle.
•
Do not use the on-off switch more than
twice a minute
work as well as resolution of function dis-
ruptions only when the drive is switched off
(pull the mains plug or turn off the hauler
and remove the ignition key).
•
To exchange the saw blade, also unlatch
the rocker inside (unhook Hook "A") Fig.
03.
•
Open the saw blade guard (loosen both hex
screws M6 "E") Fig. 05.
•
To lock the saw blade, stick the clamping
bold through the lower saw blade guard. "I"
Fig. 08.
Loosen the hex screw "J" with the provided
•
saw blade key. Remove the saw blade
flange "K" and then remove the saw blade
"L" Fig. 08.
•
Replace the saw blade.
•
Tighten the hex screw „J" with open-end
wrench to 90 Nm
•
Remount the saw blade guard.
Notes for working with the combined rocker
circular saw (1536 0903)
If you want to use this machine with the electric
drive, the PTO drive shaft cover (Fig. 13-O)
must be mounted.
Without this cover, the machine does not run in
the electric drive.
strong pressure, it may give only approx. 10-15
mm.
Now remount the cover and retighten the hex
screws ("N", Fig. 11).
Lubricating points (Fig.15)
Regularly lubricate all moving parts of your
rocker circular saw.
All pivot points on the hinged shield (Fig.15,
„R") should be lubricated to ensure the ease of
movement.
D GB
Werbung
Inhaltsverzeichnis
Fehlerbehebung
