Transport (Fig. 34,35); Maintenance; Storage; Electrical Connection - Scheppach HS110 Bedienungsanleitung

Caution:
Always hold the guided workpiece irmly and nev-
er the free workpiece which is cut off.
• Always push the transverse stop (31) so far for-
wards until the workpiece is completely cut through.
• Switch the saw off again. Only remove sawing
waste when the saw blade has come to a standstill.
Cutting chipboard
To prevent the cutting edges from breaking when cut-
ting chipboard, do not set the saw blade higher than 5
mm above the thickness of the workpiece.
After sawing
1. Switch off the circular table saw first and then the
extraction unit. The saw blade continues to run for
a longer time.
2. Do not remove the cut waste on the saw table until
the saw blade has returned to its rest position.
3. Disconnect the circular table saw from the mains
by pulling the mains plug out of the power outlet.
4. Allow the circular table saw to cool down com-
pletely.
Removing trapped material
m WARNING! Risk of injury!
Improper handling of the circular table saw may result
in serious injury.
• Switch off the circular table saw immediately and
disconnect the mains plug from the power outlet if
the saw blade is jammed in the workpiece or other
blockages occur.
• Use protective gloves and do not touch the saw
blade with your bare hands.

12. Transport (Fig. 34,35)

1. Turn the power tool off before it is transported and
disconnect it from the power supply.
2. Always carry the electric tool with at least one oth-
er person. Do not carry the machine by the table
extensions, but only lift it by the housing.
3. Protect the power tool against knocks, jolts and
strong vibrations, e.g. when it is transported in
motor vehicles.
4. Secure the power tool against tilting and sliding.
5. Never use the protective devices for handling or
transport.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

13. Maintenance

m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
• Keep the safety devices, air vents and motor hous-
ing as free of dust and dirt as possible. Wipe the
device off with a clean cloth or blow it out with com-
pressed air at a low pressure.
• We recommend that you clean the device immedi-
ately after every use.
• Clean the device regularly with a damp cloth and
some soft soap. Do not use any detergents or sol-
vents; these might attack the plastic parts of the
device. Make sure that no water can get into the
interior of the device.
• Oil the moving parts once a month in order to ex-
tend the tool life. Do not oil the motor.
Carbon brushes
If excessive sparks are generated, have an electri-
cian check the carbon brushes. Attention! The car-
bon brushes must only be replaced by an electrician.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brush, saw blade, batteries, ta-
ble inserts, push stick, push handle, V-belt
* Not necessarily included in the scope of delivery!

14. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.

15. Electrical Connection

The installed electric motor is connected ready for
operation. The connection complies with the relevant
VDE and DIN regulations. The customer's network
connection and any extension cable used must com-
ply with these regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection condi-
tions. This means that its use at freely selectable
connection points is not permitted.
GB | 39