Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Handling the Remote Controller
Inserting and Replacing Batteries
Your air conditioning unit may come with two
batteries(some units). Put the batteries in the
remote control before use.
Slide the back cover from the remote control
1.
downward, exposing the battery compartment.
Insert the batteries, paying attention to match
2.
up the (+) and (-) ends of the batteries with
the symbols inside the battery compartment.
3.
Slide the battery cover back into place.
BATTERY NOTES
For optimum product performance:
• Do not mix old and new batteries, or
batteries of different types.
• Do not leave batteries in the remote control
if you don't plan on using the device for more
than 2 months.
BATTERY DISPOSAL
Do not dispose of batteries as unsorted
municipal waste. Refer to local laws for proper
disposal of batteries.
TIPS FOR USING REMOTE CONTROL
• The remote control must be used within 8
meters of the unit.
The unit will beep when remote signal is
•
received.
Curtains, other materials and direct sunlight
•
can interfere with the infrared signal receiver.
Remove batteries if the remote will not be
•
used more than 2 months.
NOTES FOR USING REMOTE CONTROL
The device could comply with the local national
regulations.
In Canada, it should comply with
•
CAN ICES-3(B)/NMB-3(B).
In USA, this device complies with part 15 of the
•
FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference,
and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications not approved by the
party responsible for compliance could void
user's authority to operate the equipment.
54
Buttons and Functions
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the How to Use Basic Functions
ON/OFF
Turns the unit on or off.
TEMP
Increases temperate in
1°C (1°F) increments.
Max. temperature is
30°C (86°F).
NOTE: Press together
&
buttons at the same time
for 3 seconds will alternate
the temperature display
between the °C & °F.
SET
Scrolls through operation
functions as follows:
Fresh(
)
Sleep(
)
Follow Me(
)
AP mode(
)
Fresh...
The selected symbol will
flash on the display area,
press the OK button to
confirm.
TEMP
Decreases temperature
in 1 C(1 F) increments.
O
O
Boost
Min. temperature is
16 C(60 F).
O
O
FAN SPEED
Selects fan speeds in the
following order: AU
20%
40%
60%
80% 100%.
Press the TEMP
or
button
to increase/decrease the fan
speed in 1% increments.
SWING
TURBO
BOOST
Starts and stops the horizontal
Enables unit to reach preset
louver movement. Hold down
temperature in shortest
for 2 seconds to initiate vertical
possible time
louver auto swing feature(some units).
RG10A2(B2S)/BGEFU1
Model:
Model:
RG10A2(B2S)/BGEFU1
RG10A10(B2S)/BGEF(20-28 C/68-82 F)
RG10A10(B2S)/BGEF(20-28 C/68-82 F)
RG10A(B2S)/BGEF, RG10A(B2S)/BGEFU1( Fresh feature is not available)
RG10A(B2S)/BGEF, RG10A(B2S)/BGEFU1( Fresh feature is not available)
RG10A2(B2S)/BGCEFU1, RG10A2(B2S)/BGCEF(Cooling only models,
RG10A2(B2S)/BGCEFU1, RG10A2(B2S)/BGCEF(Cooling only models,
AUTO mode and HEAT mode are not available)
AUTO mode and HEAT mode are not available)
section of this manual.
MODE
Scrolls through operation modes
as follows: AUTO COOL
DRY HEAT FAN
ECO/GEAR
Press this button to enter the
energy efficient moce in a
sequence of following:
ECO
GEAR(75%)
GEAR(50%)
Previous setting
mode
ECO ......
OK
Used to confirm the selected
functions
TIMER
Set timer to turn unit on or off
BREEZE AWAY
This feature avoids direct air flow
blowing on the body and makes
you feel indulging in silky coolness.
NOTE: This feature is available
under cool, Fan and Dry mode only
CLEAN
Used to start/stop the Self Clean or
Active Clean function or 56°C
sterilization.(Model dependent,
please refer to the USER'S
OPERATION &
INSTALLATION MANUAL for
details)
LED
Turns indoor unit's LED display and
air conditioner buzzer on
and off(model dependent), which
create a comfortable and quiet
environment.
O
O
55
Werbung
Kapitel
Fehlerbehebung
