Scheppach HM120L Originalbetriebsanleitung Seite 26

position on both sides. (see Fig. 11)
• Open the set screw (29) on the moveable stop rail
(28) and push the moveable stop rail (28) outwards.
• The moveable stop rail (28) must be locked in a posi-
tion far enough from the inner position that the dis-
tance between the stop rail (28) and the saw blade
(7) is no more than 5 mm. (see Fig. 12)
• Before making the cut, check that no collision could
occur between the stop rail (28) and the saw blade (7).
• Tighten the set screw (29) again.
• Loosen the locking handle (13) counterclockwise and
pull the indexed position lever (12) with the index fin-
ger at top.
• Set the turntable (16) to the desired angle by using
the locking handle (13). The pointer (14) on the turn-
table (16) must match with the desired angular scale
(15) on the fixed saw table (17).
• Turn the locking handle (13) clockwise to fix the turn-
table (16).
• Cut as described under section 8.4.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/11-14)
The crosscut saw can be used to make mitre cuts of 0°
- 45° to left/right in relation to the work face.
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28a/28b) must be fixed at
the outer position.
• Open the locking screw (29) for the adjustable stop
rail (28) and push the adjustable stop rail (of inclined
side) outwards. (see Fig. 13+14)
• The other adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the dis-
tance between the stop rail (28) and the saw blade (7)
amounts to a maximum of 5 mm. (see Fig. 12)
• Before making a cut, check that the stop rail (28) and
the saw blade (7) cannot collide.
• Secure the locking screw (29) again.
• Move the machine head (5) to the top position.
• Fix the rotary table (16) in the 0° position.
• Loosen the locking lever (22) and use the handle (1)
to angle the machine head (5) to the left/right, until
the pointer (20) indicates the desired angle measure-
ment on the scale (19).
• Re-tighten the locking lever (22).
• Cut as described in section 8.4.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 1-2/11-14)
The crosscut saw can be used to make mitre cuts to the
left/right of 0°- 45° in relation to the work face and, at
the same time, 0°- 45° to the left or 0°- 45° to the right
in relation to the stop rail (double mitre cut).
Important. To make miter cuts (inclined saw head),
the adjustable stop rail (28) must be fixed at the
outer position.
• Open the locking screw (29) for the adjustable stop
rail (28a/28b) and push the adjustable stop rail (of in-
clined side) outwards. (see Fig. 13+14)
• The other adjustable stop rail (28) must be fixed far
enough in front of the innermost position that the dis-
tance between the stop rail (28) and the saw blade (7)
26 GB
amounts to a maximum of 5 mm. (see Fig. 12)
• Before making a cut, check that the stop rail (28) and
the saw blade (7) cannot collide.
• Secure the locking screw (29) again.
• Move the machine head (5) to its upper position.
• Loosen the locking handle (13) counterclockwise and
pull the indexed position lever (12) with the index fin-
ger at top.
• Set the turntable (16) to the desired angle by using
the locking handle (13). The pointer (14) on the turn-
table (16) must match with the desired angular scale
(15) on the fixed saw table (17).
• Turn the locking handle (13) clockwise to fix the turn-
table (16).
• Loosening the locking lever (22).
• Use the handle (1) to angle the machine head (5) to
the left/right, until the pointer (20) indicates the de-
sired angle measurement on the scale (19). (in this
connection see also section 8.6).
• Re-tighten the locking lever (22).
• Cut as described under section 8.4.
8.8 Limiting the cutting depth (Fig. 3)
• The cutting depth can be infinitely adjusted using the
screw (26). To do this loosen the knurled nut on the
screw (26). Move the stop for the cutting depth limi-
tre (27) to the outside. Turn the screw (26) in or out
to set the required cutting depth. Then re-tighten the
knurled nut on the screw (26).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (21) for sawdust
and chips.
Squeeze together the metal ring on the dust bag and
attach it to the outlet opening in the motor area.
The debris bag (21) can be emptied by means of a zip-
per at the bottom.
8.10 Changing the saw blade (Fig. 15-18)
Remove the power plug!
Important.
Wear safety gloves when changing the saw blade.
Risk of injury!
• Blade guard (6) open
• Loosen the screw (36)
• Blade guard (6) upwards until it is held
• Firmly press the saw shaft lock (4), and slowly turn
the flange screw (32) clockwise. After max. one turn,
the saw shaft lock (4) engages.
• Then undo the flange screw (32), by applying a slight-
ly greater force in a clockwise direction.
• Fully unscrew the flange screw (32) and remove the
outer flange (33).
• Then remove the saw blade (7) from the inner flange
(39) and pull out in a downwards direction.
• Carefully clean the flange screw (32), outer flange
(33) and inner flange (39).
• Insert the new saw blade (7) in the reverse sequence
and tighten.
• Position the guide bar (40) on the pin (36) again, and