Protecting The Environment - DeWalt DW717XPS Bersetzt Von Den Originalanweisungen

english
WARNING: Continued use of a platform with several
kerfs may cause loss of material control and possible
injury.
Dust extraction (fig. A2 & A3)
• Fit the dustbag (27) onto the dust spout (26).
WARNING! Whenever possible, connect a dust
extraction device designed in accordance with the
relevant regulations regarding dust emission.
Saw blades
To obtain the stated cutting capacities, always use 250 mm saw
blades with 30 mm arbor holes.
Transporting (fig. A1, A2 & B)
In order to conveniently carry the mitre saw, a carrying handle
(10) has been included on the top of the saw arm.
• To transport the saw, lower the head and depress the lock
down pin (22).
• Lock the rail lock knob with the saw head in the front
position, lock the mitre arm in the full left mitre angle, slide
the fence (3 & 8) completely inward and lock the bevel lever
(20) with the saw head in the vertical position to make the
tool as compact as possible.
• Always use the carrying handle (10) or the hand indentations
(24) shown in fig. B to transport the saw.
MAINTENANCE
Your D WALT power tool has been designed to operate over a
e
long period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories,
before adjusting or changing set-ups or when
making repairs. Be sure the trigger switch is in the
OFF position. An accidental start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Before use, carefully check the upper blade guard, movable
lower blade guard as well as the dust extraction tube to
determine that it will operate properly. Ensure that chips, dust
or workpiece particle cannot lead to blockage of one of the
functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow
the instructions given in section Mounting the Saw Blade.
Remove the jammed parts and reassembling the saw blade.
44
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen collecting
in and around the air vents. Wear approved eye
protection and approved dust mask when performing
this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the materials used
in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
WARNING: To reduce the risk of injury, regularly
clean the table top.
WARNING: To reduce the risk of injury, regularly
clean the dust collection system.
WORKLIGHT CLEANING
• Carefully clean sawdust and debris from worklight lens with
a cotton swab. Dust build-up can block the worklight and
prevent it from accurately indicating the line of cut.
• DO NOT use solvents of any kind; they may damage the
lens.
• With blade removed from saw, clean pitch and build-up from
blade.
Optional Accessories (fig. A5, A6)
WARNING: Since accessories, other than those
offered by D WaLt, have not been tested with
e
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
D WaLt, recommended accessories should be used
e
with this product.
SAW BLADES: ALWAYS USE 250 mm SAW BLADES WITH
30 mm ARBOUR HOLES. SPEED RATING MUST BE AT
LEAST 4000 RPM. Never use a smaller diameter blade. It will
not be guarded properly. Use crosscut blades only! Do not use
blades designed for ripping, combination blades or blades with
hook angles in excess of 5°.
BLADE DESCRIPTIONS
APPLICATION
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose
Fine Crosscuts
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
Consult your dealer for further information on the appropriate
accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle
electrical products and batteries according to local provisions.
Further information is available at www.2helpU.com.
DIAMETER TEETH
250 mm 40
250 mm 60
250 mm 80