Electrical Safety; Using An Extension Cable - DeWalt DW717XPS Bersetzt Von Den Originalanweisungen

english
DO NOT use under wet conditions or in presence of flammable
liquids or gases.
These miter saws are professional power tools.
DO NOT let children come into contact with the tool. Supervision
is required when inexperienced operators use this tool.
WARNING! Do not use the machine for purposes
other than intended.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons without
supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.

Electrical Safety

The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your tool is double insulated in accordance with
EN61029;
therefore no earth wire is required.
WARNING: 115 V units have to be operated via a
fail-safe isolating transformer with an earth screen
between the primary and secondary winding.
In case of cord replacement the tool must only be repaired by an
authorized service agent or by qualified electrician.
Mains Plug Replacement
(U.K. & Ireland only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the earth
terminal.Follow the fitting instructions supplied with
good quality plugs. Recommended fuse: 13 A.
Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
• The plug fitted should be comply with BS EN 60309
(BS4343),
16 Amps, earthing contact position 4h.
WARNING: Always ensure that the cable clamp is
correctly and securely fitted to the sheath of the cable.

Using an Extension Cable

If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
ASSEMBLY
WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories,
before adjusting or changing set-ups or when
38
making repairs. Be sure the trigger switch is in the
OFF position. An accidental start-up can cause injury.
Unpacking (fig. A1, B)
• Remove the saw from the packing material carefully using
the carrying handle (10).
• Release the rail lock knob (16), and push the saw head back
to lock it in the rear position.
• Press down the operating handle (11) and pull out the lock
down pin (22), as shown.
• Gently release the downward pressure and allow the arm to
rise to its full height.
Bench mounting (fig. C)
• Holes (25) are provided in all four feet to facilitate bench
mounting.
Two different sized holes are provided to accommodate
different sizes of bolts. Use either hole; it is not necessary
to use both. Bolts with a diameter of 8 mm and 80 mm
in length is suggested. Always mount your saw firmly to
prevent movement. To enhance the portability, the tool can be
mounted to a piece of 12.5 mm or thicker plywood which can
then be clamped to your work support or moved to other job
sites and reclamped.
• When mounting your saw to a piece of plywood, make sure
that the mounting screws do not protrude from the bottom
of the wood.
The plywood must sit flush on the work support. When
clamping the saw to any work surface, clamp only on the
clamping bosses where the mounting screw holes are
located. Clamping at any other point will interfere with the
proper operation of the saw.
• To prevent binding and inaccuracy, be sure the mounting
surface is not warped or otherwise uneven. If the saw rocks
on the surface, place a thin piece of material under one saw
foot until the saw is firm on the mounting surface.
Mounting the saw blade (fig. D1–D4)
WARNING: To reduce the risk of injury, turn unit
off and disconnect machine from power source
before installing and removing accessories,
before adjusting or changing set-ups or when
making repairs. Be sure the trigger switch is in the
OFF position. An accidental start-up can cause injury.
• Never depress the spindle lock button while the
blade is under power or coasting.
• Do not cut light alloy and ferrous metal (containing
iron or steel) or masonry or fibre cement product
with this mitre saw.
• Depress the head lock up release lever (12) to
release the lower guard (2),then raise the lower guard
as far as possible.
• With the lower guard held in the raised position, depress
the spindle lock button (14) with one hand, then use the
supplied
blade spanner (23) in the other hand to loosen the left-hand
threaded blade locking screw (37) by turning clockwise.
; the
2
WARNING! To use the spindle lock, press the button
as shown and rotate the spindle by hand until you feel
the lock engage.
Continue to hold the lock button in to keep the spindle from
turning.
• Remove the blade locking screw (37) and the outside arbor
collar (38).