Safety Regulations; Layout And Items Supplied - EINHELL TC-SY 18/60 Li-Solo Originalbetriebsanleitung

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 18)
1. Danger! - Read the operating instructions to
reduce the risk of injury.
2. Caution! Wear ear-muff s. The impact of noi-
se can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust
which is injurious to health can be generated
when working on wood and other materials.
Never use the device to work on any materi-
als containing asbestos!
4. Caution! Wear safety goggles. Sparks ge-
nerated during working or splinters, chips and
dust emitted by the device can cause loss of
sight.
5. Caution! Wear gloves.
6. Note! Disassemble and clean the equipment
immediately after each use. This is the only
way to keep the wetted parts clean and pre-
vent clogging. Parts that are not cleaned can
become clogged, causing an equipment fault.
7. Store the batteries only in dry rooms with
an ambient temperature of +10°C to +40°C.
Place only fully charged batteries in storage
(charged at least 40%).

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Anl_TC_SY_18_60_Li_SPK13.indb 18 Anl_TC_SY_18_60_Li_SPK13.indb 18
GB

2. Layout and items supplied

2.1 Layout (Fig. 1-4, 13, 16)
1. Air cap retaining ring
2. Air cap
3. Nozzle
4. Locking lever
5. Trigger
6. Max. paint volume control
7. Pistol mounting
8. Viscosity cup
9. Wall storage hook
10. Material tube connection
11. Material tube
12. Container
13. Fluid needle (plastic)
14. Trigger unit
15. Drive unit
16. Filter cap
A. Cleaning needle
B. Adapter for fl uid needle
a. Battery capacity indicator
b. Battery capacity indicator (LEDs)
c. Pushlock button
d. Li-ion battery pack (not included)
e. Power-X-Charger (not included)
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
- 18 -
14.01.2021 13:35:44 14.01.2021 13:35:44