Emptying The Waste Water Tank; Interrupting Operation; Ending Operation; Storing The Device - Kärcher BR 30/1 C Bp Bedienungsanleitung

5. Activate the boost function to clean stubborn dirt
(see chapter General notes on operation).

Emptying the waste water tank

● Empty the waste water tank as soon as the fresh
water tank is empty, or the device no longer absorbs
moisture, and water remains on the floor.
1. Press the ON/OFF switch.
Illustration I
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Disengage the two locking flaps on the device.
Illustration L
The waste water tank releases from the device.
4. Lift the device and set it aside.
5. To transport it to the emptying point, do not hold the
waste water tank by the lid, but with both hands on
the side of the drip tray. Keep the waste water tank
level, otherwise waste water can escape.
6. Empty the waste water tank.
Illustration M
In the case of stubborn dirt, rinse out the waste wa-
ter tank with tap water (see chapter Cleaning the
waste water tank).
7. Clean the sweep bins (see chapter Cleaning the
sweep bins).
8. Insert the waste water tank into the device in reverse
order.

Interrupting operation

ATTENTION
Risk of damage due to moisture and detergents as
well as the device tipping over
Risk of material damage on sensitive floors and on the
cleaning rollers due to prolonged exposure to moisture
and detergents.
Risk of material damage if the device falls over.
Always move the device to the parking position when
you take a break from work and after work.
Do not lean the device against walls, doors or other ob-
jects when setting it down.
1. Press the ON/OFF switch.
Illustration I
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
Rinsing the cleaning rollers
The rinsing function can be used for intermediate clean-
ing of the cleaning rollers in case of severe dirt accumu-
lation.
Note
At the end of work and before storing the device, the
cleaning rollers must be removed and cleaned under
running water or in the washing machine (see chapter
Cleaning the cleaning roller). The rinsing function does
not replace final basic cleaning.
1. Press the ON/OFF switch.
Illustration I
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Check the filling level in the fresh water tank, it must
be at least 50%.
If necessary, fill the fresh water tank accordingly
(see chapter Filling the fresh water tank).
16
4. Press and hold the Boost function button.
Illustration N
5. Press and hold the ON/OFF switch.
After approx. 3 s, the rinsing function is activated,
the cleaning rollers rotate and are rinsed.
The ON/OFF switch flashes.
6. Release the Boost function button and the ON/OFF
switch.
7. The device switches off automatically after approx.
2 minutes.
The rinsing function can be ended at any time by
pressing the ON/OFF switch.
8. Empty the waste water tank (see chapter Emptying
the waste water tank).
9. Check the filling level in the fresh water tank, if nec-
essary fill the fresh water tank accordingly (see
chapter Filling the fresh water tank).
1. Press the ON/OFF switch.
Illustration I
The device switches off.
2. Bring the device into the parking position (see chap-
ter General notes on operation).
3. Press the battery pack unlocking button, and pull the
battery pack out of the battery mount.
Illustration O
4. Charge the battery pack.
Also charge partly discharged battery packs after
use.
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device completely after
each application.
5. Clean the device (see chapter Cleaning the device).

Storing the device

ATTENTION
Risk of damage and odour development from liq-
uids and damp dirt
Liquids and damp dirt in the device can lead to bacterial
accumulation and odour development when not in use
or in storage.
Damp dirt can dry up in the device and on the cleaning
rollers, and impair the cleaning performance of the de-
vice.
Empty the fresh water tank and waste water tank at the
end of work and before storing the device.
Clean the waste water tank, the sweep bins and the
cleaning rollers.
Allow the clean cleaning rollers to dry in the air, e.g.
mounted on the device on standing vertically. Do not
place wet cleaning rollers on moisture-sensitive surfac-
es, in closed containers or cupboards.
1. Clean the device (see chapter Cleaning the device).
2. Clean the waste water tank (see chapter Cleaning
the waste water tank).
3. Clean the sweep bins (see chapter Cleaning the
sweep bins).
4. Clean the cleaning rollers (see chapter Cleaning
the cleaning roller).
5. Charge the battery pack (see operating instructions
for the battery pack and charger).
English

Ending operation