Intended Use; Preparation For Use - 3M STIHL G22 Bedienungsanleitung

МАҚҰЛДАУЛАР
Бұл өнімдер жыл сайын келесі кеңселерде мақұлданады жəне аудиттеледі; BSI Group, Нидерланды Б.В.
Сэй ғимараты, Джон М. Кейнстейн 9, 1066 ЕП Амстердам, Нидерланды, 2797 уəкілетті органы жəне /
немесе BSI Assurance UK Ltd, Kitemark Court, Davy Avenue, Knowlhill, Milton Keynes MK5 8PP, Ұлыбритания,
№ 0086 уəкілетті органы. Бұл өнімдер Еуропалық регламенттің (ЕО) 2016/425 талаптарына жəне
қолданыстағы жергілікті заңнамаға сəйкес келеді. Қолданылатын Еуропалық / жергілікті заңдар мен
уəкілетті орган www.3m.com/Head/certs мекен-жайы бойынша Сəйкестік сертификаттарын жəне
Декларацияны (ларды) қарау арқылы анықталуы мүмкін.
An
3M™ Industrial Safety Helmets

INTENDED USE

This product meets the requirements of EN397:2012, Industrial Safety Helmets. This product is designed to protect
the wearer against objects likely to strike the head. For specific performance requirements see Technical
Specification. See all instructions for use and save for continuing reference.
^ Particular attention should be given to warning statements where indicated.
^ WARNING
• Always be sure that the complete product is:
- Suitable for the application;
- Fitted correctly;
- Worn during all periods of exposure;
- Replaced when necessary.
• Proper selection, training, use and appropriate maintenance are essential in order for the product to
help protect the wearer from impact hazards.
• Failure to follow all instructions on the use of these personal protection products and/or failure to
properly wear the complete product during all periods of exposure may adversely affect the wearer's
health, lead to severe or life threatening illness or permanent disability.
• For suitability and proper use follow local regulations, refer to all information supplied or contact an
occupational hygienist, safety professional or 3M representative on the Tech Assist Helpline 3M
Australia 1800 024 464, 3M New Zealand 0800 364 357.
• For adequate protection this helmet must fit or be adjusted to the size of the users head.
• The helmet is made to absorb the energy of a blow by partial destruction or damage to the shell and the
harness, and even though such damage may not be readily apparent, any helmet subjected to severe impact
should be replaced.
• The attention of users is also drawn to the danger of modifying or removing any of the original component parts
of the helmet, other than as recommended by the helmet manufacturer. Helmets should not be adapted for the
purpose of fitting attachments in any way not recommended by the helmet manufacturer.
• Do not apply paints, solvents, adhesives or self-adhesive labels, except in accordance with instructions from the
helmet manufacturer.
• Direct contact with sprays, fluids or other substances containing solvents and/or alcohols can reduce the
durability of the helmet and should therefore be avoided.
• Use of the helmet should be kept within industrial areas only and the helmet should not be used in any other
application such as horse riding or bike riding.
• Always ensure that the head harness is well maintained and correctly adjusted to the users head.
• If in doubt contact your safety officer or 3M for further advice.

PREPARATION FOR USE

Inspection Before each use the helmet should be inspected for cracks, cuts or other damage and should be
rejected and disposed of if these are discovered. If required, replace the complete head harness assembly only.
Fitting
Insert the 4 harness holders into the helmet grooves (See figure 1). It is important that the headbands are properly
tensioned in their attachments. The 3M™ H700, G3000 and G3501 safety helmets are also approved with the
suspension rotated through 180°.
90