Introduction; Layout; Scope Of Delivery - Scheppach HM90LXU Originalbetriebsanleitung

1. Introduction

:
MANUFACTURER
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spa-
re parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating inst-
ructions before installing and commissioning the de-
vice. The operating instructions are intended to help
the user to become familiar with the machine and
take advantage of its application possibilities in ac-
cordance with the recommendations. The operating
instructions contain important information on how to
operate the machine safely, professionally and eco-
nomically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu-
lations that apply for the operation of the machine in
your country. Keep the operating instructions packa-
ge with the machine at all times and store it in a plas-
tic cover to protect it from dirt and moisture. Read the
instruction manual each time before operating the
machine and carefully follow its information. The ma-
chine can only be operated by persons who were ins-
tructed concerning the operation of the machine and
who are informed about the associated dangers. The
minimum age requirement must be complied with.
In addition to the safety requirements in these opera-
ting instructions and your country's applicable regu-
lations, you should observe the generally recognized
technical rules concerning the operation of woodwor-
king machines.
We cannot accept any liability for damage or acci-
dents which arise due to a failure to follow these inst-
ructions and the safety instructions.
20 GB
2. Layout (Fig. 1-21)
1 Handle
2 Release lever
3 ON/OFF switch
4 Machine head
5 Movable blade guard
6 Saw blade
7 Clamping device
8 Workpiece support
9 Locking screw for workpiece support
10 Table insert
11 Locking screw for turntable
12 Locking lever for fixed angle
13 Pointer
14 Scale
15 Turntable
16 Fixed saw table
17 Stop rail
18 Sawdust bag
19 Scale
20 Pointer
21 Locking screw for drag guide
22 Drag guide
23 Locking screw
24 Fastening bolt
25 Screw for cutting depth limiter
26 Stop for cutting depth limiter
27 Adjustment screw (90°)
28 Adjustment screw (45°)
29 Flange bolt
30 Outer flange
31 Saw shaft lock
32 Inner flange
33 Laser
34 ON/OFF switch for laser
35 Guide bar
a) 90° stop angle (not supplied)
b) 45° stop angle (not supplied)
c) Hexagon nut
d) Knurled nut
e) Allen key, 6 mm

3. Scope of delivery

• Open the packaging and remove the device ca-
refully.
• Remove the packaging material as well as the pa-
ckaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!