ATIKA 1600 Bedienungsanleitung Und Ersatzteile Seite 15

♦ The cutter automatically draws the shredding material into the
machine through the slow rotation of the cutting rollers.
♦ Do not allow the chopped material to pile up too high in the
area of the ejection opening. This can lead to chopped
material blocking the ejection channel, and backing up to the
filler opening.
♦ Clean out the filler opening and ejection channel thoroughly if
the machine becomes blocked. Before doing this, switch the
motor off and disconnect the machine from the mains power
supply.
♦ Automatic switch-over in the direction of rotation:
If the unit suddenly clogs, the blades may start to turn in the
opposite direction and push the shredded material back
out.
Switch off unit
−
Wait until the blades come to a standstill
−
Switch unit back on and use material which is easier to
−
process.
♦ If the machine is overloaded, a protective motor switch
ensures that the machine turns itself off automatically
turn the shredder on again after about 5 minutes
−
during those five minutes you cannot turn the machine
−
on. See point "Operational faults".
A A d d j j u u s s t t i i n n
The cutting unit has been adjusted at the factory and need
not be adjusted prior to being put into operation for the first time.
It is possible to adjust the counter blade at the cutting roller free
of clearance. For an effective operation, an as small as possible
clearance should be maintained.
Soft material or wet branches may tear instead of being cut. A
counter blade that is worn after repeated use may also lead to
this problem.
M a
M a
• Each time before starting maintenance work
switch off the motor and withdraw the mains plug
−
wear protective gloves to prevent injury.
−
Take care when maintaining the cutting equipment to ensure that
the cutters can still be operated by the starter mechanism, even
if the motor is not running because the cover has been unlocked.
Downloaded from www.Manualslib.com
g g t t h h e fixed counter blade e
Setting the clearance.
Switch on the device.
To adjust the clearance, insert
the supplied socket wrench A
and turn it to the right so that
the screw moves towards the
cutting roller. Turn until fine
aluminium chips are falling
from the ejection slot.
i n t e n a n c e a n d C a r e
i n t e n a n c e a n d C a r e
manuals search engine
• Generally garden shredders require little maintenance.
To maintain their efficiency and a long life, observe the
following:
keep vent slits clean and free from obstructions.
−
check the locking screws (tighten where necessary)
−
clean the device after shredding
−
the shredder should not be cleaned with high pressure
−
cleaners or running water.
treat the cutting roller after every use with a biodegradable
−
spray oil as protection against corrosion.
the cutting roller and shaving plate are expendable parts,
−
though with normal use and correct adjustment they have a
service life of many years.
G u
G u
• The manufacturer will supply a two years warranty after
supply of the machine from the dealer's store for faults in
material and/or workmanship.
• Warranty claims, even during the warranty period, will not be
accepted for damages due to incorrect handling or
inadequate packaging during return of the devices or to a
non-observance of the operating instructions.
• Faulty components should be returned to the factory, postage
and freight paid. Discretion for the supply of replacements
free of charge will remain with the manufacturer.
• The guarantee does not cover normal wear to: cutting roller,
shaving plate and impellers, as well as the respectively
associated fasteners.
• All warranty work will be carried out by the manufacturer. The
handling of repairs by third parties shall require prior written
consent of the manufacturer.
• The warranty will only apply of original spare parts are used.
• Subject to alterations due to further development.
• All plastic parts have been marked to facilitate sorting and
recycling. To have your used appliances recycled, contact the
manufacturer. The manufacturer will tell you how much
recycling currently costs.
14
a r a n t e e
a r a n t e e