Attaching The Auxiliary Handle; Attaching And Replacing Roughing / Grinding / Cutting Discs; Switching On And Off - Parkside PWS 230 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

is beyond the angle of the auxiliary
handle
could injure yourself against the grinding or
cutting disc.
j
Open the clamping lever
j
Insert the disc cover guide
projection
j
Turn the disc guard cover
position (working position). The closed side of
the disc guard cover
the operator.
j
Close the clamping lever
the disc guard cover
If necessary the clamping force of the connection
can be adjusted by tightening or loosening the
adjuster screw
Ensure that the disc guard cover
on the spindle collar.

Attaching the auxiliary handle

Q
CAUTION! For safety reasons this
device must always be used with the
auxiliary handle
you could become injured.
J
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
j
Screw the auxiliary handle
or on the top of the head of the device.
Attaching and replacing
Q
roughing / grinding / cutting discs
Take note of the dimensions of the roughing /
grinding or cutting discs. The circular hole must fit
on to the mounting flange without play. Do not use
a reducer piece or adapter.
J
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
J
Check the condition of the roughing /
grinding or cutting discs. They must be
free of damage, moisture or cracks.
Downloaded from www.Manualslib.com
(see Fig. B). Otherwise you
6
.
8
with the coded
7
in the coded groove
9 16
into the desired
7
must always be facing
7
to firmly clamp
8
in place.
7
.
10
7
in place. Otherwise
6
DANGER OF INjURy!
on the left, right
6
DANGER OF INjURy!
manuals search engine
Otherwise they could break up during use and
cause injury.
DANGER OF BURNS! Always wear
protective gloves when changing a
roughing / grinding or cutting disc.
Roughing / grinding and cutting discs become
. hot during use. Do not touch them until after
they have cooled down.
J
NOTE: Always ensure the discs are free of dirt
before use.
J
Use only abrasive consumables or tools with
an allowable speed at least as high as the
no-load speed of the device.
J
DANGER OF INjURy! Press the spindle lock
button
has reached a standstill.
j
sits firmly Press the spindle lock button
j
Release the clamping nut
(see Fig. C).
17
j
Place the roughing / grinding or cutting disc on
to the mounting flange
facing towards the device.
j
Then replace the clamping nut
raised side facing upwards, on to the mounting
spindle
j
Press the spindle lock button
j
Tighten the clamping nut
spanner
j
NOTE: Replace a new disc immediately if it
runs unevenly or vibrates after being exchanged.
j
After replacing a disc let the device run under
no-load conditions for 30 seconds as a safety
check. Look out for unusual noises or generation
of sparks. Check that all the fastened-on parts
are correctly attached.
j
Pay attention to see that the arrow showing the
direction of rotation on the roughing / grinding
or cutting discs (including diamond cutting discs)
corresponds with the direction of rotation of the
device (see arrow on the head of the device).
Operation
Q

Switching on and off

Q
Note: Always switch on the angle grinder before
bringing it into contact with the workpiece material.
Preparing for use / Operation
only after the mounting spindle
11
to block the drive.
11
using the spanner
13
with its labelled side
15
13
.
14
to block the drive.
11
again with the
13
.
17
14
, with its
GB/CY 15