Herunterladen Inhalt Inhalt Diese Seite drucken

Attaching The Auxiliary Handle; Attaching And Replacing Roughing / Grinding / Cutting Discs; Switching On And Off - Parkside PWS 230 SE Bedienungs- Und Sicherheitshinweise

Winkelschleifer
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

j
Close the clamping lever
the disc guard cover
If necessary the clamping force of the connection
can be adjusted by tightening or loosening the
adjuster screw
Ensure that the disc guard cover
on the spindle collar.

Attaching the auxiliary handle

Q
CAUTION! For safety reasons this
device must always be used with the
auxiliary handle
you could become injured.
J
WArNING!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
j
Screw the auxiliary handle
or on the top of the head of the device.
Attaching and replacing
Q
roughing / grinding / cutting discs
Take note of the dimensions of the roughing /
grinding or cutting discs. The circular hole must fit
on to the mounting flange without play. Do not use
a reducer piece or adapter.
J
WArNING!
Pull the mains plug out of the mains
socket before you carry out any task
on the device.
J
Check the condition of the roughing /
grinding or cutting discs. They must be
free of damage, moisture or cracks.
Otherwise they could break up during use and
cause injury.
DANGEr OF BUrNS! Always wear
protective gloves when changing a
roughing / grinding or cutting disc.
Roughing / grinding and cutting discs become
hot during use. Do not touch them until after
they have cooled down.
J
NOTE: Always ensure the discs are free of dirt
before use.
Downloaded from
www.Manualslib.com
to firmly clamp
8
in place.
7
.
10
sits firmly
7
in place. Otherwise
6
DANGEr OF INjUry!
on the left, right
6
DANGEr OF INjUry!
manuals search engine
Preparing for use / Operation
J
Use only abrasive consumables or tools with
an allowable speed at least as high as the
no-load speed of the device.
J
DANGEr OF INjUry! Press the spindle lock
button
only after the mounting spindle
11
has reached a standstill.
j
Press the spindle lock button
j
Release the clamping nut
(Fig. C).
17
j
Place the roughing / grinding or cutting disc on
to the mounting flange
facing towards the device.
j
Then replace the clamping nut
raised side facing upwards, on to the mounting
spindle
.
14
j
Press the spindle lock button
j
Tighten the clamping nut
spanner
.
17
j
NOTE: Replace a new disc immediately if it
runs unevenly or vibrates after being exchanged.
j
After replacing a disc let the device run under
no-load conditions for 30 seconds as a safety
check. Look out for unusual noises or generation
of sparks. Check that all the fastened-on parts
are correctly attached.
j
Pay attention to see that the arrow showing the
direction of rotation on the roughing / grinding
or cutting discs (including diamond cutting discs)
corresponds with the direction of rotation of the
device (see arrow on the head of the device).
Operation
Q

Switching on and off

Q
Note: Always switch on the angle grinder before
bringing it into contact with the workpiece material.
Switching on the device:
j
Press the safety lock-out
Then press the ON / OFF switch
Switching off the device:
j
Release the ON / OFF switch
14
to block the drive.
11
using the spanner
13
with its labelled side
15
, with its
13
to block the drive.
11
again with the
13
(see Fig. H).
3
.
2
.
2
GB/IE/CY
15

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis