Setting The Clock; Proceed As Follows; Using Immediate-Start Function - Silvercrest 16463 Bedienungs- Und Sicherheitshinweise

ries and / or damage of the appliance.
Now place the steam trays
1 - 2 - 3 succession (please see the markings on
the handles) on top of the condensate collec-
tion basin
Place the cover
steam tray
steam can exhaust.
Connect the mains plug
In the LCD-display, the time indicator
appear (see fig. A).
Now your steamer is ready for use.

Setting the clock

Proceed as follows:

Simultaneously press the PROG
ON / OFF
nal tone will be heard on releasing the buttons.
Press the PLUS button
indicator by 10 minutes each time. Press the
MINUS button
20
Press the PROG button
The LCD-display
clock time (clock time mode).

Using Immediate-Start Function

Note: Consider that the base of the appliance /
water tank
up to the MIN mark
in addition to the condensate collection basin
has been correctly positioned.
Press the ON / OFF button
play
of 45 minutes (see fig. B).
Note: If you do not press any button within
5 seconds you will hear a signal tone, the pilot
lamp
start the steaming process automatically.
Press the PLUS / MINUS button
or reduce the steaming time in 5 minute steps.
Note: The maximum steaming time is 90 minutes.
Downloaded from www.Manualslib.com
3 ,
7 .
centrically so that the upper
1
is completely closed and no
3
18 to a suitable socket.
buttons for 2 - 3 seconds. A sig-
14
16 to increase the time
to reduce the time indicator
16
by 1 minute each time.
17 to confirm your setting.
will now show the current
13
has to be filled with water at least
10
9 . Ensure that the turbo ring
14 . The LCD dis-
will show the factory-set steaming time
13
will glow red and the appliance will
15
manuals search engine
Note: Be aware that you might have to replen-
4 , 6 in ish water when the steaming time is longer.
Use the openings on the sides of the conden-
sate collection basin
of the appliance / water tank
the MAX mark
1 hour of steaming.
ATTENTION! HAZARD OF BURNS!
Make sure that the water does not exceed the
will MAX mark
20
out of the steamer during operation.
5 seconds after the last button has been pressed
a signal tone will be heard. The pilot lamp
will glow red and the appliance will start the
steaming process automatically.
The LCD-display
steaming time.
ATTENTION! HAZARD OF BURNS! The
17 and appliance will become hot during use. Beware
of getting in contact with the ascending steam
or any components.
If the set steaming time is elapsed, the appli- If the set steaming time is elapsed, the appli-
ance will automatically switch back to the
keep-warm mode (see "keep-warm mode").
Note: During the steaming process, the steam-
ing time can be increased or reduced in 5
minute steps at any time by pressing the
PLUS / MINUS button
is manually reduced to '0', the appliance will
switch over to keep-warm mode (see "keep-
warm mode") automatically.
ATTENTION! HAZARD OF BURNS!
Always lift the cover
from you and let the steam exhaust backwards.
8 Do not bend over the appliance during steam
7 generation. Use oven cloths when touching the
cover
a long fork or tongs when checking if the food
is done.
Press the ON / OFF button
steaming process prematurely or to switch off
the appliance. The indicator on the LCD-display
13 switches back to the time indicator
again (see fig. A).
Note: If the supply of water is used up during
16 to increase use, a signal tone will sound. The steaming
process gets stopped. The indicator on the
LCD-display
Initial Operation
for refilling. If the base
7
10 is filled up to
, it will be sufficient for approx.
19
. Otherwise, hot water may spurt
19
will indicate the remaining
13
16 . If the steaming time
1 slowly, turning away
and the steam trays ,
1 3
to terminate the
14
switches back to the time indi-
13
GB/IE/CY
15
, . Use
4 6
20
9