Christopeit CX 4 Montageanleitung Und Bedienungsanleitung Seite 22

Step 3:
Installation of the handgrip (12) and footrest holder (36) at
connecting tubes (21).
1. Push the handgrip bars (12L+12R) onto the connecting tubes
(21L+21R) and adjust the holes in the tubes so that they are
aligned.
(Note: the handgrip bars must be aligned after assembly so that
the upper ends are inclined outwards (away from the support
(25)).
2. Push the bolt (14) through the holes and tighten the handgrip
bars (12) with curved washers (13) and spring washer (15) firmly.
3. Push the footrest holder (36R) at the connecting tube (21R) and
adjust the holes in the tubes so that they are aligned.
4. Push the allan bolt (35) through the holes and tighten the footrest
holder (36R) at connection tube (21R) with washers (41) and nut
(40).
(This connection point has to move easily. So please don't
tighten the screw too much.)
5. Install the left footrest holder (36L) incl. all additionally required
parts on the left hand side of the machine as described in 3. – 4.
Step 5:
Installation of the footrests (44) at footrest holder (36).
1. Push the right footrest (44R) onto the footrest holder (36R).
Adjust the holes in the parts so that they are aligned.
2. Push the screws (43) from above through the holes. Push on
a washer (77) and spring washer (78) from the opposite side,
screw on a handgrip nut (79) and tighten firmly.
3. Install the left footrest (44L) on the left footrest holder (36L) as
described in 1. – 2. (Note: The position adjusted in this way
should always be equal at both sides. The right and left footrests
can be discerned by the edges of the longitudinal sides of the
footrests. The high edges of the footrests (44) must point inwards
(towards the main frame.) The positions can change as desired
at all times by removing the carriage bolts (43) and sliding the
footrests on the footrest brackets to get a comfortable exercise
position close to the hand grip.)
Step 4:
Installation of the footrest holder (28) with connecting tubes (21)
to the pedal crank (63) and the support (25).
1. Place the preassembled unit of the right footrest holder (36R)
and connecting tube (21R) at the right hand side of the main
frame (68). (Note: Right is specified as viewed standing on the
machine during training.)
2. Push the axle (27) into the middle position at handlebar support
(25) and put one washer (23) and the connecting tube (21R) onto
the axles' end (25). Put on the screw (17) a spring washer (15)
and a washer 8//32 (18) and tighten it firmly.
3. Put the foot pedal holder (86) at the pedal crank (63) and tighten
them with washer 8//20 (70), spring washer (15) and screw (17)
firmly.
4. Install the left footrest holder (36L) incl. all additionally required
parts on the left hand side of the machine as described in 1. – 3.
5. Now turn the construction by hand 3-4 times and tighten the
screws (14) of support (25) as mentioned in Step 2 firmly.
Push the plastic cover (37) into the right position of chain cover.
6. Mount plastic cover set (33L+33R) to both side front end of
pedal bar (36) and secure with screws (34) for each side.
7. Mount foot pedal cover (84) to both side rear end of pedal bar
holder (86) and secure with screws (85) for each side.
8. Mount handlebar cover set (24L-1+24L-2) to the handle bar
support (25) and secure with screws (22).
9. Mount hand grip cover sets (20L-1+20L-2) and (20R-1+20R-2)
to both connection tubes (21) and secure with screws (22) for
each side.
22