Herunterladen Inhalt Inhalt Diese Seite drucken

Safety Advice Relating Specifically To This Device; Safety Advice / Operation; Assembly - Parkside PTBM 500 Bedienungs- Und Sicherheitshinweise

Vorschau ausblenden Andere Handbücher für PTBM 500:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

18. remain alert.
J
Watch what you are doing. Proceed with
caution. Do not use electrical power tools if
you cannot concentrate.
19. Check the electrical power tool for
damage.
J
Before the electrical power tool is used any
further, carefully check the safety equipment
and any slightly damaged parts to see that
they are still working properly.
J
Check that all moving parts on the tool are
working properly, can move freely and are not
damaged. All parts must be correctly attached
and fulfil all the requirements necessary to allow
the electrical power tool to operate properly.
J
Damaged safety equipment and components
must be properly repaired or replaced at a
competent electrical equipment repair centre
unless otherwise indicated in the operating
instructions.
J
Damaged switches must be replaced at a
Customer Service Centre.
J
Never use an electrical power tool that cannot
be switched on and off properly.
20. CaUTIOn!
J
The use of inserted tools and accessories other
than those recommended by the manufacturer
could lead to you being injured.
21. Have your electrical power tool repaired at an
electrical equipment repair specialist.
J
This electrical power tool complies with the rel-
evant safety regulations. Repairs may only be
carried out by a specialist electrical repair cen-
tre using original spare parts, otherwise injury
could occur to the user.
Safety advice relating
specifically to this device
J
CaUTIOn: Too high a pressure overloads the
motor and reduces the drilling speed
J
Always use sharp drill bits
J
Cool the drill bit with a suitable liquid
J
Use a special drill bit for drilling into stainless
steel
J
Check before every use that the chuck
drilling table
and all the threaded fasteners
19
E-3470_Table_Drill_PTBM500_Content_LB5.indd 29
are properly fixed in place and seated.
J
Check that the interlock switch
drive / belt cover
bench press drill must switch off automatically
when the drive / belt cover
J
Never remove drilling debris with your hand.
Failure to observe this advice may lead to injury.
J
Do not wear gloves whilst working with the
bench press drill. Failure to observe this advice
may lead to the gloves becoming wound
around the revolving parts.
J
WarnInG! Be aware that persons operat-
ing the device or in its vicinity may be at risk of
being in contact with or inhaling dusts. Take all
the necessary safety precautions in relation to
dusts.
J
WarnInG! Keep your working area clean.
Mixtures of materials can be particularly dan-
gerous. Light metal alloy dust, for example,
may burn or explode.
WarnInG!
SHOCK FrOM METaL DUST! Machining
metal can result in electrically conductive dust
being deposited inside the device. Operate the
device through a residual current device (RCD)
with a trip current of 30 mA.
J
Do not drill materials containing asbestos.
Asbestos is a known carcinogen.
J
Do not drill moist materials or damp surfaces,
J
Never leave the device working unattended,
J
Never use the device for a purpose for which it
was not intended.
J
Always work with the mains lead leading
away from the rear of the device.
Operation
Q

assembly

Q
The bench press drill is supplied ready to assemble.
j
First clean the corrosion-protection coated
parts (column
the chuck
3
, the
assemble the press drill:
3
j
Sit the column

Safety advice / Operation

under the
29
is working properly: The
6
is opened.
6
DanGEr OF ELECTrIC
, the base, the vice
23
13
) e.g. with a dry cloth.
on the base plate
23
18
GB/MT
17.03.2008 16:23:03 Uhr
and
and
29

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis