Operating Procedures; Turning On The Power - Panasonic AW-PH400E Bedienungsanleitung

Operating procedures

w Turning on the power
When using one pan/tilt control panel (AW-RP400), set its EXT CONT [M/S] switch to the [M] position.
When two AW-RP400 units are used, set the EXT CONT [M/S] switch on the AW-RP400 to which the pan-tilt head is
connected to the [M] (master) position and the switch on the AW-RP400 to which the pan-tilt head is not connected to the
[S] (slave) position.
Turn on the power.
Follow the sequence below to turn on the power when one AW-RP400 is going to be used: Set the power switch of the
AC adapter used for the AW-RP400 and the AC power switch on the indoor pan/tilt head (AW-PH400) to [ON], set the
OPERATE switch on the remote operation panel (AW-CB400) to [ON], and then set the OPERATE switch on the
AW-RP400 to [ON].
Follow the sequence below to turn on the power when two AW-RP400 units are going to be used: Set the OPERATE
switches of the AW-CB400 and of the AW-RP400 set as the slave to [ON], and then set the OPERATE switch on the
AW-RP400 set as the master to [ON].
w Setting the movement range (limiters) of the indoor pan/tilt head (AW-PH400)
If there are any objects obstructing the movement of the indoor pan/tilt head (AW-PH400) in the immediate vicinity, set
restrictions on the movement range (limiters: left, right, top and bottom limits of rotation).
When the roll unit (AW-RL400) is connected to the pan/tilt control panel (AW-RP400), set the movement limits (clockwise and
counterclockwise limits) of the roll unit as well.
Before using these units, set these limits without fail.
p When it is shipped, the AW-PH400 is set up to be placed on a stand or base. If it is to be suspended from the ceiling, the
mounting direction switch must be set without fail. If this setting is not performed correctly, the directions of the pan/tilt
operations will be reversed, and the movement range (limiter) settings of the pan-tilt head will not be stored in the memory
properly. For details on the setting methods and related aspects, refer to "Setting the mounting direction switch" in the
operating instructions for the AW-PH400.
Now proceed with the settings for the pan/tilt control panel (AW-RP400).
Use the CONTROL SELECT buttons to select the pan-tilt head whose movement range (limiters) is to be set.
To set the left limit, use the PAN/TILT lever to rotate the pan-tilt head as far as the left limit which is to be set.
While holding down the MENU/LIMIT button, press the PRESET MEMORY button [5]. Once the limit is set, the lamp of
the PRESET MEMORY button [45] will light.
To release the setting, press the PRESET MEMORY button [5] again while holding down the MENU/LIMIT button.
Once the setting is released, the lamp of the PRESET MEMORY button [50] will light.
To set the right limit, use the PAN/TILT lever to rotate the pan-tilt head as far as the right limit which is to be set.
While holding down the MENU/LIMIT button, press the PRESET MEMORY button [10]. Once the limit is set, the lamp of
the PRESET MEMORY button [45] will light.
To release the setting, press the PRESET MEMORY button [10] again while holding down the MENU/LIMIT button.
Once the setting is released, the lamp of the PRESET MEMORY button [50] will light.
To set the top limit, use the PAN/TILT lever to rotate the pan-tilt head as far as the top limit which is to be set.
While holding down the MENU/LIMIT button, press the PRESET MEMORY button [15]. Once the limit is set, the lamp of
the PRESET MEMORY button [45] will light.
To release the setting, press the PRESET MEMORY button [15] again while holding down the MENU/LIMIT button.
Once the setting is released, the lamp of the PRESET MEMORY button [50] will light.
To set the bottom limit, use the PAN/TILT lever to rotate the pan-tilt head as far as the bottom limit which is to be set.
While holding down the MENU/LIMIT button, press the PRESET MEMORY button [20]. Once the limit is set, the lamp of
the PRESET MEMORY button [45] will light.
To release the setting, press the PRESET MEMORY button [20] again while holding down the MENU/LIMIT button.
Once the setting is released, the lamp of the PRESET MEMORY button [50] will light.
60 (E)