Panasonic AW-PH400E Bedienungsanleitung Seite 34

Pan/Tilt Control Panel AW-RP400
Parts and their function
 MEMORY button
When one of the () PRESET MEMORY selection
buttons [1] to [50] is pressed while holding down the
MEMORY button, the settings of the pan-tilt head system
can be registered in that PRESET MEMORY selection
button.
The MEMORY button flashes if the pan-tilt head selected
by the ( ) CONTROL SELECT button is not connected
or its power has not been turned on.
 PRESET MEMORY selection buttons [1] to [50]
Use these buttons to call the settings registered in them.
When data has been registered in the tracing memories,
the recording/play time displays appear.
 LCD panel
The current setting statuses are displayed on this panel.
 MENU/LIMIT button
Hold down this button for 2 or more seconds to turn the
setting menu ON or OFF.
When () PRESET MEMORY selection button [5], [10],
[15], [20], [25] or [30] is pressed while holding down the
MENU/LIMIT button, ON/OFF control over the limiters
can be exercised.
 CONT dial
This is used for the setting menu operations.
TALLY lamps [1] to [5]
When tally signals are supplied to the ($) TALLY/INCOM
connectors [1] to [5] on the rear panel, the lamps with the
numbers corresponding to those connectors light up.
When tally signals are supplied to the tally connectors [1]
to [5] of the remote operation panel (AW-CB400), if this
panel is connected to the pan/tilt control panel, the lamps
with the numbers corresponding to those connectors also
light up.
CONTROL SELECT buttons [1] to [5]
The (') CONTROL OUT TO PAN/TILT HEAD [P1] to [P5]
connectors on the rear panel can be selected by pressing
buttons [1] to [5]. The button lamps corresponding to the
numbers of the buttons selected light, and the selected
pan-tilt head systems can be controlled.
When the (() MONI SEL OUT connector on this control
panel is connected to the MONI SEL IN connector on the
cable compensation unit (AW-RC400), the images of the
selected camera can be output to the MONI1 or MONI2
connector on the AW-RC400.
p When 2 AW-RP400 are connected, the combination of
the control panels which select the monitor output can
be set on the menu.
ANOTHER CONTROL lamps [1] to [5]
When another AW-RP400 is connected, these lamps
indicate the numbers of the pan-tilt head systems
selected by the additional AW-RP400.
TRACING MEMORY [START POINT, START,
STOP, RESTORE, RESET, 1 to 10] buttons
Use these for the tracing memory operations. For details
on operation, refer to the tracing memory section.
SPEED controls
[ZOOM/FOCUS/PAN/TILT/ROTATION]
These enable the pan-tilt head, lens and roll unit control
speeds to be adjusted.
By turning these controls as far as they will go in the
counterclockwise direction, operation of the pan-tilt
heads and lenses can be prevented even when control is
exercised using the joystick, etc.
! PAN/TILT lever/ROTATION control switch
Use these to adjust the direction of the pan-tilt heads.
When the lever is tilted to the left or right, the pan-tilt
heads move toward the left or right; when it is tilted up or
down, they move upward or downward. The movement
speed can be adjusted by the angle to which the lever is
tilted.
Further, the angle of the roll unit (AW-RL400) can be
adjusted using the ROTATION control switch on the front
of the lever. By pressing the top part of the ROTATION
control switch, the roll unit rotates clockwise; by pressing
the bottom part, it rotates counterclockwise. The speed
of the rotation changes in accordance with the amount of
pressure applied.
33 (E)