Siemens SINUMERIK 840D sl Bedienhandbuch Seite 16
Drehen
Vorschau ausblenden
Andere Handbücher für SINUMERIK 840D sl:
- Funktionshandbuch (2196 Seiten) ,
- Handbuch (1886 Seiten) ,
- Diagnose-handbuch (1476 Seiten)
Inhaltsverzeichnis
Werbung
Inhaltsverzeichnis
10.3.1
Allgemeines..........................................................................................................................449
10.3.2
Darstellung der Kontur .........................................................................................................450
10.3.3
Neue Kontur anlegen ...........................................................................................................451
10.3.4
Konturelemente erstellen .....................................................................................................453
10.3.5
Passungsmaß eingeben ......................................................................................................459
10.3.6
Kontur ändern ......................................................................................................................460
10.3.7
Konturaufruf (CYCLE62) - nur bei G-Code-Programm ........................................................461
10.3.8
Abspanen (CYCLE952)........................................................................................................462
10.3.9
Abspanen Rest (CYCLE952) ...............................................................................................472
10.3.10
Stechen (CYCLE952)...........................................................................................................474
10.3.11
Stechen Rest (CYCLE952) ..................................................................................................481
10.3.12
Stechdrehen (CYCLE952) ...................................................................................................483
10.3.13
Stechdrehen Rest (CYCLE952) ...........................................................................................489
10.4
Fräsen ..................................................................................................................................492
10.4.1
Planfräsen (CYCLE61).........................................................................................................492
10.4.2
Rechtecktasche (POCKET3) ...............................................................................................495
10.4.3
Kreistasche (POCKET4) ......................................................................................................505
10.4.4
Rechteckzapfen (CYCLE76) ................................................................................................515
10.4.5
Kreiszapfen (CYCLE77).......................................................................................................521
10.4.6
Mehrkant (CYCLE79)...........................................................................................................528
10.4.7
Längsnut (SLOT1)................................................................................................................533
10.4.8
Kreisnut (SLOT2) .................................................................................................................542
10.4.9
Offene Nut (CYCLE899) ......................................................................................................550
10.4.10
Langloch (LONGHOLE) - nur bei G-Code-Programm .........................................................560
10.4.11
Gewindefräsen (CYCLE70)..................................................................................................562
10.4.12
Gravur (CYCLE60)...............................................................................................................566
10.5
Konturfräsen.........................................................................................................................573
10.5.1
Allgemeines..........................................................................................................................573
10.5.2
Darstellung der Kontur .........................................................................................................573
10.5.3
Neue Kontur anlegen ...........................................................................................................574
10.5.4
Konturelemente erstellen .....................................................................................................577
10.5.5
Kontur ändern ......................................................................................................................582
10.5.6
Konturaufruf (CYCLE62) - nur bei G-Code-Programm ........................................................583
10.5.7
Bahnfräsen (CYCLE72) .......................................................................................................584
10.5.8
Konturtasche/Konturzapfen (CYCLE63/64) .........................................................................590
10.5.9
Konturtasche vorbohren (CYCLE64) ...................................................................................592
10.5.10
Konturtasche fräsen (CYCLE63)..........................................................................................597
10.5.11
Konturtasche Restmaterial (CYCLE63, Option)...................................................................603
10.5.12
Konturzapfen fräsen (CYCLE63) .........................................................................................606
10.5.13
Konturzapfen Restmaterial (CYCLE63, Option)...................................................................611
10.6
Weitere Zyklen und Funktionen ...........................................................................................615
10.6.1
Schwenken Ebene / Ausrichten Werkzeug (CYCLE800).....................................................615
10.6.2
Schwenken Werkzeug (CYCLE800) ....................................................................................622
10.6.2.1
Ausrichten von Drehwerkzeugen - nur bei G-Code-Programm (CYCLE800) ......................622
10.6.2.2
Ausrichten von Fräswerkzeugen - nur bei G-Code-Programm (CYCLE800).......................625
10.6.2.3
Anstellen von Fräswerkzeugen - nur bei G-Code-Programm (CYCLE800).........................626
10.6.3
High Speed Settings (CYCLE832) .......................................................................................627
10.6.3.1
Parameter ............................................................................................................................630
10.6.4
Unterprogramme ..................................................................................................................631
10.6.5
An Beladung anpassen (CYCLE782)...................................................................................633
16
Bedienhandbuch, 06/2019, A5E44903486A AB
Drehen
Werbung
Inhaltsverzeichnis
