3M PELTOR WS ALERT XP Bedienungsanleitung Seite 9

CAUTION
• Risk of explosion if battery is replaced by an incorrect type.
• Always use product-specific 3M replacement parts. Use of
unauthorized replacement parts may reduce the protection
you receive from this product.
NOTE:
• When worn according to the user instructions, this hearing
protector helps reduce exposure to both continuous noises,
such as industrial noises and noises from vehicles and
aircraft, as well as very loud impulse noises, such as
gunfire. It is difficult to predict the required and/or actual
hearing protection obtained during exposure to impulse
noises. Proper selection, fit and use of hearing protection,
proper care of hearing protection, and other variables will
impact performance. To learn more about hearing protection
for impulse noise, visit www.3M.com.
• This earmuff is provided with level-dependent attenuation.
The wearer should check correct operation before use. If
distortion or failure is detected, the wearer should refer to
the manufacturer's advice for maintenance and replacement
of the battery.
• This hearing protector limits the entertainment audio signal
to 82 dBA effective to the ear.
• Operating temperature range: –20 °C to 55 °C
• Storage temperature range: –20 °C to 55 °C
APPROVALS
Hereby, 3M Svenska AB declares that the radiobroadcast
receiver and Bluetooth radio communication is in compliance
®
with Directive 2014/53/EU and other appropriate directives to
fulfill the requirements for the CE marking.
3M Svenska AB also declares that the PPE type headset is
in compliance with Regulation (EU) 2016/425 or Community
Directive 89/686/EEC.
The applicable legislation can be determined by reviewing
the Declaration of Conformity (DoC) at www.3M.com/peltor/
doc. The DoC will also show if some other type-approvals
are also applicable. When retrieving your DoC, please locate
your part number. The part number of your earmuffs can be
found at the bottom of one cup. An example can be seen in
the picture below.
The PPE is audited annually (if Category III products) and
type approved by Finnish Institute of Occupational Health,
Notified Body No. 0403, Topeliuksenkatu 41 b, FI-00250
Helsinki, Finland. The product has been tested and approved
in accordance with EN 352-1:2002 / EN 352-3:2002,
EN 352-4:2001/A1:2005, EN 352-6:2002, EN 352-8:2008.
A copy of the DoC and additional information required in
** 3M™ PELTOR™ WS™ ALERT™ XPI Headset
the Directives can also be obtained by contacting 3M in the
country of purchase. For contact information, see last pages
of this user instruction.
This product contains electrical and electronic
components and must not be disposed of using standard
refuse collection. Please consult local directives for disposal
of electrical and electronic equipment.
LABORATORY ATTENUATION
Explanation of attenuation tables
EN 352-1/EN 352-3/EN 352-4
Research suggests that users may receive less noise reduction
than indicated by the attenuation value(s) on the packaging,
due to variation in fit, fitting skill, and motivation of the user.
Refer to your applicable regulations for guidance on how to
adjust label values and estimate attenuation. In addition, 3M
strongly recommends fit testing of hearing protectors.
A:1 Frequency (Hz)
A:2 Mean attenuation (dB)
A:3 Standard deviation (dB)
A:4 Assumed protection value, APV (dB)
A:5
H = Hearing protection estimation for high frequency sounds
(ƒ ≥ 2000 Hz).
M = Hearing protection estimation for medium frequency
sounds (500 Hz < ƒ < 2000 Hz).
L = Hearing protection estimation for low frequency sounds
(ƒ ≤ 500 Hz).
A:6 Criterion Level
H = Criterion level for high frequency noise
M = Criterion level for medium frequency noise
L = Criterion level for low frequency noise
Compatible Industrial Safety Helmets EN 352-3
These earmuffs should be fitted to and used only with, the
industrial safety helmets listed in Table B. These earmuffs
were tested in combination with the following industrial safety
helmets and may give different levels of protection if fitted to
different helmets.
Explanation of the industrial safety helmet attachment table:
B:1 Helmet manufacturer
B:2 Helmet model
B:3 Attachment
B:4 Head size: S = small, M = medium, L = large
Headband MRX21A2WS6*, MRX21A3WS6*
D:1 Headband (PVC, PA)
D:2 Headband wire (stainless steel)
D:3 Two-point fastener (POM)
D:4 Cushion (PVC foil and PUR foam)
D:5 Foam liner (PUR foam)
D:6 Cup (ABS)
D:7 Level-dependent microphone for ambient listening (PUR
foam)
EN
2