3M PELTOR WS ALERT XP Bedienungsanleitung Seite 12

EN
Connected to phone and two-way radio. **
Operating phone. ** (see fig. 7)
Bluetooth
®
State
button
Incoming call
Outgoing call/Call
in progress
Ongoing reception
on two-way radio
Short press
and incoming call
Ongoing phone
call and reception
on two-way radio
Incoming call
Long press
Call in progress
NOTE: When connected to a two-way radio you cannot
control the audio playback unit from the headset. **
NOTE: If you have an ongoing phone call, you will hear two
beeps for incoming calls on the two-way radio. To end the call
and switch to the incoming two-way radio call, short press (1 s)
the Bluetooth button [
®
button [ ] one more time to listen to the two-way radio or
wait for the next incoming two-way radio message. **
NOTE:
To maintain noise cancelling performance, the speech
microphone should be positioned very close to your mouth
(less than 3 mm) (G:1).
DID YOU KNOW: The headset supports Bluetooth
A2DP 1.3 from different apps or from the phone's media
player.
DID YOU KNOW: Audio playback will be automatically
paused from audio playback unit when you have a call in
progress or a two-way radio message. ** After ending the call
/ message the audio playback will automatically start again.
SMART TIP: If the headset has been reset to factory default,
it automatically enters pairing mode the first time the headset
is powered on again.
5
Action
Answer
End call
Answer
End call
Reject
Toggle call between
phone/headset
]. Short press (1 s) the Bluetooth
streaming
®
** 3M™ PELTOR™ WS™ ALERT™ XPI Headset
Bluetooth 4.2
®
Bluetooth is a global wireless communication standard that
®
connects devices together over a certain distance. Think
headset and phone, speaker and PC to smartphone and
more. Read more on www.bluetooth.com.
Bluetooth profiles HSP 1.2, HFP 1.6, A2DP 1.3, AVRCP 1.6.
®
More info on https://www.bluetooth.org/tpg/listings.cfm.
CONFIGURING YOUR HEADSET (fig. 11)
Long press (2 s) the Menu button [M] to access the
configuration menu. A voice message will confirm "Menu".
Short press (1 s) the Menu button [M] to navigate through the
menu. A voice message will confirm each menu step. Short
press (1 s) the [ + ] or [–] button to activate/deactivate/change
different configurations.
The following options exists in the configuration menu:
1. Bluetooth pairing (fig. 6)
®
When the voice message says "Bluetooth
press (1 s) the [ + ] button to start pairing. Short press (1 s) the
[–] button to stop pairing. A voice message will confirm
pairing on". Search and select "WS ALERT XP"
"Bluetooth
®
or "WS ALERT XPI" on your Bluetooth
message will confirm when pairing is complete, "Pairing
complete" and "Connected". Short press (1 s) the [–] button to
stop the pairing. A voice message will confirm, "Pairing off".
2. Bass boost
Bass boost gives a fuller bass sound to streamed stereo
music. Short press (1 s) the [ + ] or [–] button to enable/disable
bass boost.
3. Surround balance
®
Short press (1 s) the [–] button to increase left side and
reduce right side. Short press (1 s) the [ + ] button to increase
right side and reduce left side. A voice message will notify
when the surround balance is centered, "Center".
4. Surround equalizer
Surround equalizer changes the frequency characteristics of
the surround sound. Short press (1 s) the [–] or [ + ] button to
change the surround equalizer levels, "Low – Normal – High
– Extra high".
5. Sidetone volume
Sidetone is audible feedback to the headset user during a
conversation. Short press (1 s) the [–] or [ + ] button to change
the sidetone volume, "Off – Low – Normal – High".
6. Battery type
Short press (1 s) the [–] or [ + ] button to change the battery
type to either rechargeable or alkaline.
7. Reset to factory default (fig. 12)
Short press (1 s) the [–] or [ + ] button, then long press (2 s) the
Menu button [M]. A voice message will guide you.
pairing", short
®
device. A voice
®