Contact Information - Interlogix EV1012 Serie Installationsanleitung

Product warnings THESE PRODUCTS ARE INTENDED FOR SALE
and disclaimers TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY "AUTHORIZED
DEALER" OR "AUTHORIZED RESELLER", IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
Certification
UL/cUL The product must be connected to a listed burglar
system compatible control unit or power supply
unit, which provides a minimum 4 hours of
standby power and has a voltage output between
10 and 15 VDC.
All wiring must be made according to National
Electrical Code, NFPA70, and CSA C22.1,
Canadian Electrical Code Part I, Safety Standards
for Electrical Installations.
Perform walk test at least one per year.
Use only a listed power-limited supply.
EV1012AM has not been evaluated by UL/cUL.
FCC Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the
equipment and receiver
•
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected
•
Consult the dealer or an experienced
radio/TV technician for help
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
IC This Class B digital apparatus complies with
Canadian ICES-003.
European Union UTC Fire & Security hereby declares that this
directives device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see www.utcfireandsecurity.com or
www.interlogix.com.
6 / 40
or scan the QR code.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/

Contact information

www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.utcfssecurityproducts.eu
DA: Installationsark
Introduktion
EV1000-serien omfatter modellerne EV1012 og EV1012AM.
Disse detektorer har patenteret spejl, pyro og
signalbehandlingsteknologi.
Installationsvejledning
Den anvendte teknologi i disse detektorer er modstandsdygtig
over for falske alarmer. Undgå imidlertid mulige årsager til
ustabilitet (se Figur 1), f.eks.:
• Direkte sollys på detektoren
• Kraftig træk på detektoren.
•
Varmekilder inden for detektorens synsfelt
•
Store dyr inden for detektorens synsfelt
•
Blokering af detektorens synsfelt med store genstande
som f.eks. møbler
•
Genstand under 50 cm fra anti-maskeringsdetektor (AM)
•
Installation af to detektorer mod hinanden og mindre end
50 cm fra hinanden
Installation af detektoren
Figur 7
(1) Standardtilslutning (fabriksstandard)
Dobbelt sløjfe-tilslutning
(2)
CP Central
WT Gangtest
AM Antimaskning
D/N Dag/nat
Rtest Fjernbetj test
Sådan installeres detektoren:
Tag dækpladen af og fjern skruen (se Figur 2, pkt. 1).
1.
Åbn forsigtigt detektoren med en skruetrækker (Figur 2,
2.
pkt. 2 og 3).
Gør soklen fast til væggen mellem 1,8 m og 3,0 m fra
3.
gulvet. Til fladmontering anvendes mindst to skruer
(DIN 7998) i position A. Til hjørnemontering anvendes
skruer i position B eller C (Figur 3). Til at installere
vægsabotagekontakt anvendes position A eller B.
4. Tilslut detektoren (se figur 3 og 7).
Vælg de ønskede jumper- og DIP-switch-indstillinger (se
5.
figur 5). Se "Jumper-indstillinger" på side 7, hvis du ønsker
yderligere oplysninger.
P/N 146169999-10 (ML) • REV G • ISS 29MAR19