Specifications; Regulatory Information; Contact Information - Interlogix VE1120 Series Installation Sheet

PIR Red LED Alarm relay
Low voltage Open (Alarm)
PIR intruder Open (Alarm)
alarm
PIR/AM Red Yellow
LED LED
Start up
Low voltage
PIR intruder
alarm
Latched PIR
(Memory)
AM alarm
After AM
reset
Technical
fault
Continuously on Normal blinking (1 Hz)
Fast blinking (4 Hz)
* Depends on the setting of the DIP switch SW4.

Specifications

Detector
Signal processing
Range
Optical
Memory
Input power
For UL/cUL installations
Peak-to-peak ripple
Detector start-up time
Normal current
For UL/cUL installations
Current in alarm
Maximum current
(LED on)
Mounting height
Target speed range 30 cm/s to 3 m/s
(1 ft./s to 10 ft./s)
Alarm (NC) / Tamper 80 mA, 30 VDC,
relay characteristic
Pry-off tamper (not
evaluated by UL/cUL)
AM relay characteristic
PIR Alarm time
Operating temperature
For UL/cUL installations
Dimensions (H x W x D) 125 × 55 × 60 mm
P/N 146279999-2 (ML) • REV C • ISS 28JUN12
To reset
Apply correct voltage
Automatically after 3 s
Alarm AM To reset
relay relay
Closed Closed Automatically
after 60 s
Open Open Apply correct
(Alarm) (Alarm) voltage
Open Automatically
(Alarm) after 3 s
Switch to Night
mode
Open* Open See DIP
(Alarm) (Alarm) switch 3
Switch to Night
mode
Open Do a successful
(Alarm) walk test
VE1120 VE1120AM
PIR PIR with AM
V2E
20 m
11 high-density mirror curtains
Yes
9 to 15 VDC (12 V nominal)
10 to 15 VDC (12 V nominal)
2 V (at 12 VDC)
25 s 60 s
6.5 mA 10 mA
0.078 W —
1.2 mA 3.8 mA
11 mA 24 mA
1.8 to 3.0 m (5.9 ft.to 9.8 ft.)
20 cm/s to 3 m/s
(0.65 ft./s to 10 ft./s)
80 mA, 30 VDC
resistive
Optional Onboard (yes)
— 80 mA
at 30 VDC max.
3 s
−10 to +55°C (14 to 130°F)
0 to 49°C ( 32 to 120°F )
125 × 65 × 60 mm
(4.92 x 2.16 x (4.92 x 2.6 x 2.36 in.)
2.36 in.)
Relative humidity
Weight
IP/IK rating

Regulatory information

Manufacturer UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Certification
UL/cUL The product must be connected to a listed burglar
system compatible control unit or power supply unit,
which provides a minimum 4 hours of standby power
and has a voltage output between 10 and 15 VDC.
All wiring must be made according to National
Electrical Code, NFPA70, and CSA C22.1, Canadian
Electrical Code Part I, Safety Standards for Electrical
Installations.
Perform walk test at least one per year.
Use only a listed power-limited supply.
VE1120AM has not been evaluated by UL/cUL.
FCC Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV
technician for help
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
IC This Class B digital apparatus complies with Canadian
ICES-003.
2002/96/EC (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.

Contact information

www.utcfireandsecurity.com or www.interlogix.com
VE1120 VE1120AM
95% max. noncondensing
(UL/cUL Installations)
150 g
IP30 IK02
5 / 32